Recent Content by finnracing

  1. finnracing
    Thread

    Garmin 128 Problem

    Folks I am hoping someone will be able to assist. I have a Garmin 128 on the boat. It has worked perfectly until i installed a Standard...
    Thread by: finnracing, Oct 27, 2011, 0 replies, in forum: OnBoard Electronics & Controls
  2. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Thanks Gents A great help once again.
    Post by: finnracing, Jul 21, 2010 in forum: Metal Boat Building
  3. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    CDK Thanks for the reply. The binnicle is metal assy/stand that the wheel and engine throttle is attached to in a sailing yacht. A couple of...
    Post by: finnracing, Jul 20, 2010 in forum: Metal Boat Building
  4. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    CDK Thanks for the reply. Yes that is correct. The nuts and bolts are in excerlent order but the anode itself is approx half the size it was...
    Post by: finnracing, Jul 20, 2010 in forum: Metal Boat Building
  5. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Hi Jonr We have not upgraded the shore power to the boat as yet. We will probably do so as soon as time and money allow. We were cruising of...
    Post by: finnracing, Jul 19, 2010 in forum: Metal Boat Building
  6. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Gents Many thanks Once again.
    Post by: finnracing, Jul 1, 2010 in forum: Metal Boat Building
  7. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Thanks Gents Just to clarify. Shore side add RCD. On Boat fit 16 Amp isolating transformer with 16 amp cabling. Fit 30mA 16 Amp RCD after the...
    Post by: finnracing, Jun 30, 2010 in forum: Metal Boat Building
  8. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Post by: finnracing, Jun 29, 2010 in forum: Metal Boat Building
  9. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Post by: finnracing, Jun 29, 2010 in forum: Metal Boat Building
  10. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Gemtlemen Many Thanks
    Post by: finnracing, Jun 25, 2010 in forum: Metal Boat Building
  11. finnracing
    Post

    Welding a steel craft whilst afloat - electrolysis?

    Gentlemen Please could i ask Capt Littlelegs & CDK to each post a wiring drawing of their ideal, safest 240vac shorepower installation on a...
    Post by: finnracing, Jun 24, 2010 in forum: Metal Boat Building
  12. finnracing
    Post

    Coolant lever warner

    CDK I cannot quite make out what you have attached to the back of the tungsten electrode & How have you attached it?
    Post by: finnracing, Jun 9, 2010 in forum: OnBoard Electronics & Controls
  13. finnracing
    Post

    Coolant lever warner

    CDK Thanks for all your valuable input. Just a couple of questions. What transistor have you chosen in this design? Can this device be used to...
    Post by: finnracing, Jun 8, 2010 in forum: OnBoard Electronics & Controls
  14. finnracing
    Post

    Wiring my first boat

    Excuse the ignorance gents. What length of boat would you consider installing a 24vdc system rather than 12vdc?
    Post by: finnracing, May 19, 2010 in forum: OnBoard Electronics & Controls