Gaff Masts - replace timber with aluminium

Discussion in 'Boat Design' started by Two Bob Peter, Sep 16, 2021.

  1. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    I am looking at building 2 x new aluminium masts to replace missing timber masts on a 50' gaff schooner.
    Looking for technical assistance to confirm suitability of aluminium sections and actual design specifications.
    Cheers
     
  2. bajansailor
    Joined: Oct 2007
    Posts: 3,595
    Likes: 1,560, Points: 113, Legacy Rep: 37
    Location: Barbados

    bajansailor Marine Surveyor

    G'day TBP,

    I see that you now have a Daniel Bombigher designed gaff schooner - that is quite a change from the aluminium trimaran you wanted to build a few years ago!

    Have a look at this post by TANSL on here re mast scantlings
    Mast and Rigging calculations https://www.boatdesign.net/threads/mast-and-rigging-calculations.55096/

    It is now 0500 hrs in Spain as I write this, but I am sure that @TANSL will be along soon to give you some good advice.

    I googled Bombigher's Shpountz (as mentioned on your home page) and found this sister ship for sale - she does look very fine indeed.
    I see that she has varnished wooden masts - they must need a lot of maintenance, hence I can see why you want to now go for aluminium masts.

    Bombigher 50 ft Schooner 1982 https://www.sandemanyachtcompany.co.uk/yacht/191/bombigher-50-ft-schooner-1982

    Bombigher 50' gaff schooner.jpg
     
  3. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Hi Bajansailor
    I was building on the trimaran idea until this came along and I couldn't resist. Currently not quite like "Perseverance", the one pictured, at the moment, but work is well underway.

    Cheers
     
    bajansailor likes this.
  4. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Oops - the picture is "Hollander" - now has light blue hull colour
     
  5. Old Stoker
    Joined: Feb 2020
    Posts: 14
    Likes: 2, Points: 3
    Location: Australia

    Old Stoker Junior Member

    Tom Colvins Steel boat building,vol ,,2 has all the comparison, nice boat I was aboard,Nathaniel, a 55 Sitting Bull,with drop centerboards,she is built in steel,twin 60 HP Peugeot Diesels. One of Daniels finest.
     
    bajansailor likes this.
  6. The Q
    Joined: Feb 2014
    Posts: 223
    Likes: 42, Points: 28, Legacy Rep: 21
    Location: Norfolk, UK

    The Q Senior Member

    Carbon fibre might also be worth considering, there are several carbon fibre builders who could do it
     
  7. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Thanks, I will chase up that Tom Colvin info. I saw Sitting Bull in Darwin around twenty years ago, nice boat.
     
  8. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Thanks,
    I did chase up carbon fibre, expensive option compared to aluminium or even timber. Has advantages, but for my project a bit too expensive.
    Cheers
     
  9. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Further to first comment.
    The design and currently sailing vessels have 220mm OD timber masts - and there have been no reported failures of the design, so I feel no need to re-create all the stability / strength data - just use the assumption that if the specifications of a typical timber mast can be met or exceeded with aluminium - it is only the actual engineering of the masts to be confirmed.
    I did have an engineer do a comparison between the strength of timber / aluminium with the same OD and the above aluminium thickness, the aluminium is OK (6082 T6)
    and I have done a weight assessment - aluminium works out approximately 80Kg lighter over the two masts
    My idea is;
    Use 220mm / 8.2 thickness aluminium 13m (6082 T6 - DNV ) long section upto the hounds
    Sleeve a join with a smaller diameter tube and taper this down to 120mm over 4m length.
    What I am looking for;
    Double check on strength characteristics of the selected aluminium section/grade in lieu of timber.
    Method of joining
    Method of attachment of cheeks etc

    I am not expecting anyone to volunteer the information, It will take time to put this together / communicate and I expect to have to remunerate accordingly.
    Cheers,
    Peter
     
  10. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Update.
    Thankyou for the input Bajansailor, Old Stoker, The Q.
    I have engaged an experienced Naval Architect to provide the specs. Looking forward to receiving the package so I can start the mast building process.
    Cheers, Peter
     
  11. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    Taking weight from the topsides will make the boat roll faster and may become uncomfortable.
     
  12. Two Bob Peter
    Joined: Jul 2017
    Posts: 12
    Likes: 1, Points: 3
    Location: Australia

    Two Bob Peter Junior Member

    Hi Gonzo, thanks for the comment. I have considered that. Not know exactly what the previous masts were made from but using a median of the range of densities of timber that may have been used, I didn’t think that a possible 80kg would make a lot of difference. My thought was to prefer to go lighter rather than heavier, perhaps a wrong assumption?
    Cheers, Peter
     
  13. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    80 kg times the length of the mast create a huge moment force. Have you ever been onboard a sailboat with the mast off? It is surprising how fast they roll. However the amplitude of the roll is shorter.
     
  14. TeddyDiver
    Joined: Dec 2007
    Posts: 2,614
    Likes: 136, Points: 73, Legacy Rep: 1650
    Location: Finland/Norway

    TeddyDiver Gollywobbler

    Can allways build a crows nest up to make it equal..
     

  15. Skyak
    Joined: Jul 2012
    Posts: 1,462
    Likes: 145, Points: 63, Legacy Rep: 152
    Location: United States

    Skyak Senior Member

    Masts off is a huge difference -this is not. This is the equivalent of a large crew member going two thirds up the bare mast. Would you note a significant change in comfort from that?
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.