Search Results

Search Again
Page 2 of 4
  1. GWB
    Thread

    Can Awlgrip or Interlux perfection be buffed?

    Well we painted out hull over the weekend - for the most part it came out pretty good. There are a few spots where the pressure in the gun must...
    Thread by: GWB, Jun 3, 2008, 12 replies, in forum: Fiberglass and Composite Boat Building
  2. GWB
    Post

    1-part Topside Primer over 2-part Primer

    Stan - you need to get rid of all the 1 part primer. Call Interlux, they will tell you the same thing. You cannot paint 2 pack epoxy paints over...
    Post by: GWB, Apr 28, 2008 in forum: Fiberglass and Composite Boat Building
  3. GWB
    Thread

    Exhaust design and layout

    I'm in the process of installing a new motor and exhaust system into my sailboat. My concern is the distance from the high rise exhaust where the...
    Thread by: GWB, Apr 18, 2008, 2 replies, in forum: Diesel Engines
  4. GWB
    Thread

    Best delta shaped sander?

    I need to purchase a sander like this for sanding into corners and other awkward places. Does anyone have a recommendation for a sander like this?...
    Thread by: GWB, Apr 8, 2008, 0 replies, in forum: Wooden Boat Building and Restoration
  5. GWB
    Post

    Hints on ANYTHING

    Must have been a big popsicle
    Post by: GWB, Apr 7, 2008 in forum: Fiberglass and Composite Boat Building
  6. GWB
    Post

    Maintaining a wet edge while rolling and tipping the deck

    The holes are where the interior cabin beams bolt through from the outside. I have ground out a circular area and I'm going to wet out with epoxy...
    Post by: GWB, Apr 6, 2008 in forum: Fiberglass and Composite Boat Building
  7. GWB
    Post

    Maintaining a wet edge while rolling and tipping the deck

    Here are some pictures of the deck [ATTACH] [ATTACH] [ATTACH] [ATTACH]
    Post by: GWB, Apr 6, 2008 in forum: Fiberglass and Composite Boat Building
  8. GWB
    Post

    Maintaining a wet edge while rolling and tipping the deck

    Yup - thanks
    Post by: GWB, Apr 5, 2008 in forum: Fiberglass and Composite Boat Building
  9. GWB
    Post

    The AWLGRIP Knowledge challenge

    Jim - correct me if I'm wrong but maintaining a wet edge accross the entire deck and cabin was not addressed. Are there any roll and tippers...
    Post by: GWB, Apr 5, 2008 in forum: Fiberglass and Composite Boat Building
  10. GWB
    Post

    Maintaining a wet edge while rolling and tipping the deck

    OK - will cross post, thanks
    Post by: GWB, Apr 4, 2008 in forum: Fiberglass and Composite Boat Building
  11. GWB
    Post

    The AWLGRIP Knowledge challenge

    How do you guys maintain a wet edge when rolling and tipping an entire deck and cabin? Or do you do it in sections? Thanks for any help
    Post by: GWB, Apr 4, 2008 in forum: Fiberglass and Composite Boat Building
  12. GWB
    Thread

    Maintaining a wet edge while rolling and tipping the deck

    Apologies if this has allready been covered. How am I going to paint the whole deck and cabin in one shot while maintaining a wet edge? Or do...
    Thread by: GWB, Apr 4, 2008, 7 replies, in forum: Fiberglass and Composite Boat Building
  13. GWB
    Post

    Hand sanding tools and techniques

    Yeah Jim - same boat. I have some production 5" paper with adhesive backing that I can stick to the foam block. Maybe I could cut the block to...
    Post by: GWB, Apr 3, 2008 in forum: Fiberglass and Composite Boat Building
  14. GWB
    Thread

    Hand sanding tools and techniques

    I have sanded a fair bit of my boat with my RA porter cable tool. Of course, there are areas I cannot get to with the power tool such as at the...
    Thread by: GWB, Apr 3, 2008, 11 replies, in forum: Fiberglass and Composite Boat Building
  15. GWB
    Post

    Paint to show where I have allready sanded

    Thanks for all the help
    Post by: GWB, Apr 3, 2008 in forum: Fiberglass and Composite Boat Building
  16. GWB
    Post

    Paint to show where I have allready sanded

    Thanks for the reply Grady. I'm using interlux primekote 2 part before prefection top coat. I don't understand why you say I should spray the...
    Post by: GWB, Apr 2, 2008 in forum: Fiberglass and Composite Boat Building
  17. GWB
    Thread

    Heavily oxidised hull, what grit paper before painting?

    Need to get rid of the oxidisation before painting. Thanks for any help
    Thread by: GWB, Apr 2, 2008, 1 replies, in forum: Fiberglass and Composite Boat Building
  18. GWB
    Thread

    Paint to show where I have allready sanded

    What paint should I use as a "marker" paint? I have spent hours washing down and scrubbing the deck and now I need to sand. This paint will show...
    Thread by: GWB, Apr 2, 2008, 10 replies, in forum: Fiberglass and Composite Boat Building
  19. GWB
    Post

    New installation

    Thanks for that KB. Do you perhaps have a wiring diagram that I could reference?
    Post by: GWB, Mar 24, 2008 in forum: Electrical Systems
  20. GWB
    Thread

    New installation

    I have what is probably a dumb question about a new electrical installation in a sailboat. There will be 2 batteries (house and starting) an...
    Thread by: GWB, Mar 17, 2008, 3 replies, in forum: Electrical Systems
Showing results 21 to 40 of 67 Next >
Search Again
Page 2 of 4