1. The Marketplace Forums can be useful for members who know one another well from forum discussions and offline communications and wish to post boatbuilding tools, drafting tools, molds and tooling, and other professional equipment for sale or trade. However, caution and good judgement should always be used. Especially when considering any business with anyone not already well known to you and trusted, due diligence must be used to confirm details and identity and be sure the transaction is safe before any money or property changes hands. Always use good judgement and perform due dilligence and follow these guidelines.

Anti-thft device for boats

Discussion in 'Marketplace' started by Landokia, Nov 2, 2002.

  1. Landokia
    Joined: Nov 2002
    Posts: 2
    Likes: 0, Points: 0, Legacy Rep: 10

    Landokia New Member

    I have a few anti-theft devices for sale that prevents anyone from starting a boat unless the correct personal identification number (PIN#) is entered.
    The devices uses a numeric key pad. The PIN# is a 4 digit code.
     

    Attached Files:

  2. Guest

    Guest Guest

    I take it a thief cannot simply pry this device out with a screw driver and short circuit it?
     
  3. Guest

    Guest Guest

    And is the number set at the factory or can it be reset by the owner?

    Also if you had posted the attachment as a jpg it would be much faster loading and easier to view than the bmp.
     
  4. Landokia
    Joined: Nov 2002
    Posts: 2
    Likes: 0, Points: 0, Legacy Rep: 10

    Landokia New Member

    The number is set from the factory. It cannot be changed.
    If the unit is pryed from the boat it cannot be short circuited.
    I have changed it to jpeg now
     
  5. Guest

    Guest Guest

    All a thief does is bypass the relay or cut the orange wire. It is a normally closed relay and will still allow to start. Want a real marine security system , you need a loud siren, conformal coated board to resist elements, waterproof remote controls etc. This all costs less than one hundred dollars.

    For more info email abuzz@mindspring.com
     
  6. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    The easiest way is to use a cheater box. It connects at the engine into the main harness plug. I use them all the time to troubleshoot electrical problem. It isolates the boat harness from the engine.
     
  7. brian eiland
    Joined: Jun 2002
    Posts: 5,067
    Likes: 216, Points: 73, Legacy Rep: 1903
    Location: St Augustine Fl, Thailand

    brian eiland Senior Member

    Anti-Thief for Outboards

    ...courtesy of Sail World


    There's nothing worse than the invaded feeling you get when something is stolen. But when it is your only mode of transport between boat and shore – ie. the dinghy – it's even worse. Crystal Blues crew, Ley and Neil Langford, cruising in South East Asian waters, have a simple solution, which they sought and found after having their dinghy outboard stolen from the Malaysian island of Labuan, near Brunei. The partially good news is that the thieves tried to steal the dinghy itself, but were prevented by the stainless steel wire attached. Here's their solution:

    The thieves had simply smashed off the alloy transom screw toggles, eliminating our supposedly secure fixings. Friends Joe & Janet of SV Tegan have showed us a simple tube that can be padlocked over the transom screws, to eliminate the weak point. Whilst the tube can be purchased commercially, it wasn't available in Sarawak. So we had one made by a local stainless steel fabrication shop in Miri, from square section tube that is commonly used for legs on stainless steel kitchen furniture. The first one cost about $12 and worked really well, so we had a second one made for our smaller outboard. One slot, two holes, its really very simple. The slot was cut with a plasma cutter.

    Lock detail .....

    The padlock is a stainless steel Abus Mariner, which we've found to be bomb proof in a saltwater environment, though we needed a slightly longer shackle to go through both the tube and the stainless strop. The installed photo is at right. The rubber surround on the padlock stops it rattling against the boat – nice.'
     

  8. aj_fry
    Joined: May 2008
    Posts: 3
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: perth

    aj_fry New Member

    hi i have a 18 foot aluminium dinghy and i wanted to add a floor to it it. how would one do thiis?
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.