Extra fins on rudder blade...??

Discussion in 'Hydrodynamics and Aerodynamics' started by Vronsky, Jul 26, 2016.

  1. Vronsky
    Joined: Apr 2014
    Posts: 68
    Likes: 1, Points: 8, Legacy Rep: 10
    Location: Amsterdam

    Vronsky Junior Member

    Hi all,
    I recently noticed this rudder with these extra two horizontal fins attached to the vertical blade. I'm wondering what these might be for, anyone ?

    [​IMG]

    Thanks,
    V.
     
  2. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    It's an anti-ventilation plate. It appears that particular rudder is near the surface and at the aft end of the LWL on a double ended boat. This means underway, it will likely pull down air from above, so the plate is added to prevent the rudder from losing effective area from this ventilation situation.
     
  3. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    Depends where the waterline is I suppose, but could it be an attempt to dampen pitching ?
     
  4. Vronsky
    Joined: Apr 2014
    Posts: 68
    Likes: 1, Points: 8, Legacy Rep: 10
    Location: Amsterdam

    Vronsky Junior Member

    I estimate the top of the rudder blade is a half foot below the waterline, more (1') when the boat is moving forward.

    Hullspeed of this 21' displacement mobo is around 6 knots:
    is any -serious- ventilation likely at such low velocity ??
     
    Last edited: Jul 26, 2016
  5. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    You wouldn't think so.
     
  6. mydauphin
    Joined: Apr 2007
    Posts: 2,161
    Likes: 53, Points: 48, Legacy Rep: 575
    Location: Florida

    mydauphin Senior Member

    It could just be a bad idea
     
  7. TeddyDiver
    Joined: Dec 2007
    Posts: 2,614
    Likes: 136, Points: 73, Legacy Rep: 1650
    Location: Finland/Norway

    TeddyDiver Gollywobbler

    Water aint allways flat and the velocity at the rudder (just behind the prop) can be double the hull speed, especially with rough or fouled bottom..
     
    1 person likes this.
  8. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    The photo doesn't show enough of the hull, but it can be assemd there's a fair bit of volume forward of what's visible and a significant hole being dragged behind the steep run and deadrise that is visible, which will cause some ventilation. I agree in that it appears a bit dubious at best on this hull form.
     
  9. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    That puzzles me, a rough or fouled bottom would be more inclined to slow the speed of the flow over the rudder, would it not ? ( neglecting the prop wash, which obviously increases the speed of the flow).
     
  10. TeddyDiver
    Joined: Dec 2007
    Posts: 2,614
    Likes: 136, Points: 73, Legacy Rep: 1650
    Location: Finland/Norway

    TeddyDiver Gollywobbler

    Slows the speed of the boat, right. The prop wash is the main contributor on the flow on the rudder so cannot be neglected.
     
  11. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    Of course the propwash increases the flow speed, but I'm not seeing how a rough bottom does.
     
  12. The Q
    Joined: Feb 2014
    Posts: 223
    Likes: 42, Points: 28, Legacy Rep: 21
    Location: Norfolk, UK

    The Q Senior Member

    If you look a a motor boats stern under way you often see disturbed water and wasted energy from the prop wash. I believe that, correctly or incorrectly, those wings are an attempt to direct the wash deeper into the water and give therefore more stearing thrust.
     
  13. daiquiri
    Joined: May 2004
    Posts: 5,371
    Likes: 258, Points: 93, Legacy Rep: 3380
    Location: Italy (Garda Lake) and Croatia (Istria)

    daiquiri Engineering and Design

    Trim tabs?
     
  14. JSL
    Joined: Nov 2012
    Posts: 811
    Likes: 64, Points: 28, Legacy Rep: 41
    Location: Delta BC

    JSL Senior Member

    I've put 'fences' on many rudders-- especially flat (plate type) rudders. They double as stiffening, fitted at top and bottom of blade, both sides, and project about 10% of the blade chord. If you want some real 'lift', add a fairing over the stock and a fishtail at the rudder trailing edge. Tried this on a 85' MY and the owner said he seldom had to use his stern thruster.
     

  15. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    Too wide to be "fences" imo.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.