Picture build over the winter

Discussion in 'Wooden Boat Building and Restoration' started by lewisboats, Dec 4, 2012.

  1. lewisboats
    Joined: Oct 2002
    Posts: 2,329
    Likes: 129, Points: 0, Legacy Rep: 1603
    Location: Iowa

    lewisboats Obsessed Member

    [​IMG]



    [​IMG]
     
    2 people like this.
  2. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    Your winter builds are always a pleasure to observe.
     
  3. rwatson
    Joined: Aug 2007
    Posts: 6,165
    Likes: 495, Points: 83, Legacy Rep: 1749
    Location: Tasmania,Australia

    rwatson Senior Member

    is that only 12' long ?

    It seems to have a lot of rocker if so - it may it a hard to paddle straight . Canadians are bad enough to keep straight with their high windage as it is.
     
    1 person likes this.
  4. Submarine Tom

    Submarine Tom Previous Member

    Good one Watson!!

    I give you points for that one!
     
  5. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    It's probably from having to lean a lot because of the canned beans. :D
     
  6. lewisboats
    Joined: Oct 2002
    Posts: 2,329
    Likes: 129, Points: 0, Legacy Rep: 1603
    Location: Iowa

    lewisboats Obsessed Member

    Bloody frame warped something awful. Spent a couple of hours getting it as straight as possible Got the upright frame supports installed and finished drawing the template for the center frame. Now I have to get one of the kids to come over and help with the laser level to get a base line to attach the frames to. This is going together upside down to start with then Ill flip it once it is sufficiently sturdy.

    [​IMG]
     
    1 person likes this.
  7. Oyster
    Joined: Feb 2006
    Posts: 269
    Likes: 9, Points: 0, Legacy Rep: 104
    Location: eastern United States

    Oyster Senior Member

    Well the only thing that is important is the centerline. But a suggestion, use plywood gussetts at the ends across the right angle corners. This holds the entire strongback square.
     
  8. michael pierzga
    Joined: Dec 2008
    Posts: 4,862
    Likes: 116, Points: 0, Legacy Rep: 1180
    Location: spain

    michael pierzga Senior Member

    I prefer to cover the whole strongback with plywood

    As you begin the build, set the ply decked strong back on saw horses and use it as a long workbench.

    Once all ply panels are glued, cut, and various moldings like rub rails and battens made, the strongback is moved to the floor and the mold stations set up on it.

    You waste a few sheets of ply but you save your back and do much better work when you have a proper workbench .
     
  9. lewisboats
    Joined: Oct 2002
    Posts: 2,329
    Likes: 129, Points: 0, Legacy Rep: 1603
    Location: Iowa

    lewisboats Obsessed Member

    It was decked with 1/2" ply but I fear the 2x6s were a lot more determined than the ply and took it along for the ride. The table is stable and surprisingly strong. I now have the strongback screwed to the table. The wood was stored outside unheated but under cover and I fear that the extra dryness and warmth of the house caused the problems. It's better now.
     
  10. michael pierzga
    Joined: Dec 2008
    Posts: 4,862
    Likes: 116, Points: 0, Legacy Rep: 1180
    Location: spain

    michael pierzga Senior Member

    Yah,,,wood moves. Locally they have boards of " engineered wood "

    You know the stuff, many short pieces glued together to make a long board.

    Commonly used for concrete forms and scaffolding boards. Very stable.

    Visit a local landfill and many times you can load up with old ones for free.
     
  11. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    Updates? Photos?
     
  12. lewisboats
    Joined: Oct 2002
    Posts: 2,329
    Likes: 129, Points: 0, Legacy Rep: 1603
    Location: Iowa

    lewisboats Obsessed Member

    Divorce (yay... finally after 10 years separation), Illness, (just got notified of high blood pressure, high cholesterol, leaky heart valve and funky blood chemistry), Taxes, Jury duty notice.... nothing pretty. Hoping to get back to it soon.
     
  13. Submarine Tom

    Submarine Tom Previous Member

    Geeze, life sucks.

    Get back to it as soon as possible, at (all most) any expense.

    I love canoes.

    Do you know what the similarity between making love in a canoe and American beer is?
     
  14. lewisboats
    Joined: Oct 2002
    Posts: 2,329
    Likes: 129, Points: 0, Legacy Rep: 1603
    Location: Iowa

    lewisboats Obsessed Member

    Nope!
     

  15. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    Damn Steve, you're one of our success stories, and not allowed to die yet. I still remember when you discovered a designed in powerboat hook, several years ago and seemed a bit surprised. You've learned a lot since then.
     
Loading...
Similar Threads
  1. Brian Fredrik
    Replies:
    2
    Views:
    1,219
  2. WidowsSon
    Replies:
    14
    Views:
    3,519
  3. johnnythefish
    Replies:
    7
    Views:
    1,446
  4. Boracay
    Replies:
    6
    Views:
    1,494
  5. John Perry
    Replies:
    5
    Views:
    1,529
  6. Rod Tait
    Replies:
    0
    Views:
    915
  7. Rick Goodwell
    Replies:
    10
    Views:
    1,960
  8. Sam C
    Replies:
    27
    Views:
    5,635
  9. Chris06
    Replies:
    2
    Views:
    1,226
  10. Allan Bradley
    Replies:
    9
    Views:
    4,172
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.