What is a "Cheek"??

Discussion in 'Wooden Boat Building and Restoration' started by Winingar, Aug 10, 2007.

  1. Winingar
    Joined: Jun 2007
    Posts: 33
    Likes: 1, Points: 8, Legacy Rep: 13
    Location: Oklahoma

    Winingar Junior Member

    On the pattern page for my stem assembly it shows the stem foot and the stem. There's an additional pattern on the page labeled *Cheek*.

    ???:confused:

    Probably a stupid question but, where does it go?
     
  2. lazeyjack

    lazeyjack Guest

    as I always umderstand it, piece placed on side of a member, permanent as in doublers, or removable as in the jaws of woodworkers vice, there may be colloquiel meanings
    also can be a a peice on side of wooden jack plane
     
  3. alan white
    Joined: Mar 2007
    Posts: 3,730
    Likes: 123, Points: 0, Legacy Rep: 1404
    Location: maine

    alan white Senior Member

    I'd think this set of pieces make lands for hood ends of planking. Stems can be built up or of-a-piece. If built up, the "cheek" pieces would be the outer pieces, perhaps wedge-shaped in section.

    Alan
     
  4. RHP
    Joined: Nov 2005
    Posts: 842
    Likes: 90, Points: 28, Legacy Rep: 1183
    Location: Singapore

    RHP Senior Member

    In short, a cheek is a support. Usually associated with gaff masts, the cheeks are knee shaped pieces of wood either side of the mast at the hounds which carry the trestle tree and the eyes in the end of the shrouds.

    They are also the side pieces of blocks.
     
  5. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 506, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    On a stem or in the forward sections of a keel, particularly when the forefoot is deep or the entry is fine, it's often necessary to provide "cheek" pieces. This is because of the low angle the planks land on the stem or keel. These are as Alan has suggested and are additional bearing areas attached to the sides of the stem and keel, which provide more "landing" for the hood ends of planking. Commonly these are made of the same stock as the stem or keel. The term cheek can found in several places in traditional building methods, rudder heads, gaff jaws, engine beds, etc.
     
  6. Winingar
    Joined: Jun 2007
    Posts: 33
    Likes: 1, Points: 8, Legacy Rep: 13
    Location: Oklahoma

    Winingar Junior Member

    As usual, thanks you guys. You are awesome. :cool:
     
  7. lazeyjack

    lazeyjack Guest

    no you mean chocks, mast chocks I think
     
  8. RHP
    Joined: Nov 2005
    Posts: 842
    Likes: 90, Points: 28, Legacy Rep: 1183
    Location: Singapore

    RHP Senior Member

    I'll match your 5 and raise you ten by staying with my definition and saying chocks are those wedges that position/support the mast at the point where it passes through the deck? Assumes poker face and sits back........ ;-)


    A lot of gaffer terminology is local to the part of the world where the boats were built and operated 100+ years ago. I was brought up in Hoylake, just outside Liverpool (UK) where we had a number of Morecambe Bay prawners (Nobbies) on the moorings and surrounding beaches with their own characteristics, folklore and ancient mariners still fishing them. My understanding of terms therefore comes from prawners off the beach moorings of Liverpool which may differ from other parts of the world.
     

  • Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
    When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.