How much power? (displacement hull)

Discussion in 'Boat Design' started by Bruce46, Dec 3, 2010.

  1. Bruce46
    Joined: Jul 2006
    Posts: 81
    Likes: 3, Points: 0, Legacy Rep: 49
    Location: Stuart, Fla.

    Bruce46 Junior Member

    Is there a reasonably accurate formula for calculating the horsepower required to move a displacement hull at various speed / length ratios? I was running some numbers on a 60' displacement yacht and saw that according to a formula in Skene’s the resistance on my hull more then doubles when increasing the speed from s/l of 1.1 to 1.3 (532# vs 1330#)
     
  2. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    Skene's formula is quite accurate.
     
  3. Bruce46
    Joined: Jul 2006
    Posts: 81
    Likes: 3, Points: 0, Legacy Rep: 49
    Location: Stuart, Fla.

    Bruce46 Junior Member

    My hull has a displacement of 29.56 tons, a dwl of 56.6667', beam dwl 14.75'
    Cp .62, Cb.407.
    According to the chart for max hp @ dwl I need 200 hp, however, when I use the formula for efffective hp (resistance X speed X .003) 532 X 8.3 X .003=13.25 and input that into prop efficienencies (.55) I come up with 24.1 hp to move a 66000 pound boat at 8.3 kts. If this is correct the 250 hp Cummins in her belly has had a very easy life. (She tops out at just over 13 kts)

    Thanks for your response
    Bruce
     
  4. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    The hull speed should be about 11Kt. If you go over that, the power requirements increase enourmously.
     
  5. FAST FRED
    Joined: Oct 2002
    Posts: 4,519
    Likes: 111, Points: 63, Legacy Rep: 1009
    Location: Conn in summers , Ortona FL in winter , with big d

    FAST FRED Senior Member

    The first Passagemaker book has a very good table that will answer all the speed range questions.

    Perhaps someone could post the pages?

    FF
     
  6. Pierre R
    Joined: May 2007
    Posts: 461
    Likes: 32, Points: 0, Legacy Rep: 458
    Location: ohio, USA

    Pierre R Senior Member

    David Gerr's formula work pretty good for real world numbers.

    Hp = Disp in lb/(10.665/S/L)^3

    In the case of your boat at 8.3 knots that is around 73 hp. David's formula assumes a clean bottom and a prop efficiency of around 55%. You have to adjust if you are dirty or far off the 55% mark.

    By his formula the max speed for a 250 hp Cummins is around 12.3 knots.

    A quick check of another formula of his which is max theoretical hull speed puts you right at the top

    Max S/L = 8.26/ D/L^.311 For your boat = 1.7 = 12.8 knots

    D/L = Disp in long tones/ (LWL/100)^3 for your boat = 162

    Your Cp would indicate that the designer expected you to cruise around 10 knots and burn about 7-7.5 gph depending on house load. A bit over 50% power.

    My guess is the 250hp Cummins has plenty of reserve power for headseas and such at the 10 knot cruising speed. I would call it sized about right.

    These formulas are also good for rough lie checkers. If the numbers are to good to be true you are probably dealing with a liar or a person who does not know the weight or design of his boat.
     
  7. terhohalme
    Joined: Jun 2003
    Posts: 512
    Likes: 40, Points: 28, Legacy Rep: 506
    Location: Kotka, Finland

    terhohalme BEng Boat Technology

    If the hull looks like a boat (yes Cp = 0.62 is fine) and not like a box, you need about 5 HP for each ton to reach hull speed. So if your fully loaded displacement is 30 tons, 150 HP is enough.
     

  8. FAST FRED
    Joined: Oct 2002
    Posts: 4,519
    Likes: 111, Points: 63, Legacy Rep: 1009
    Location: Conn in summers , Ortona FL in winter , with big d

    FAST FRED Senior Member

    "Skene’s the resistance on my hull more then doubles when increasing the speed from s/l of 1.1 to 1.3 (532# vs 1330#)"

    These would be reasonable inshore cruise speeds but as slow as .9 might be even better offshore as far as MPG go.

    IF willing to "go slow" the efficiency is incredible! "Hull Speed" is for sailors with free wind power, unless you love 15GPH.

    FF
     
    1 person likes this.
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.