recommendation for 8x8 amphibious propulsion

Discussion in 'Hybrid' started by jklos2002, May 24, 2011.

  1. jklos2002
    Joined: Feb 2010
    Posts: 15
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: usa

    jklos2002 Junior Member

    I'd appreciate any recommendations on propelling an 8x8 amphibious vehicle (like Argo) across calm inland waters. It doesn't need to plane out, just slow wake speed.

    Would a used PWC jet drive (seadoo, etc.) work? see photo.

    Weight is approximately 2000lbs. think small barge.

    I've seen a variety of different approaches, from outboard motors to propellers to jet drives.

    Any thoughts would be appreciated.
    Thanks!
     

    Attached Files:

    • $4.jpg
      $4.jpg
      File size:
      121.2 KB
      Views:
      1,101
    • drives.jpg
      drives.jpg
      File size:
      55.5 KB
      Views:
      1,167
  2. jklos2002
    Joined: Feb 2010
    Posts: 15
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: usa

    jklos2002 Junior Member

    Ok. given the lack of response, maybe jet-powered isn't the way to go.

    Another thought, perhaps a hydraulic system would be better? The ATV is powered by a 70hp engine with room for a clutch-engaged hydraulic pump. I'm thinking maybe a pair of smaller props to avoid having a rudder.

    Again, slow no wake speed is all that's required.


    THanks for your thoughts.
     
  3. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    It may be amphibious but what depth of water is it rated for?
    Is it top-heavy and pose a roll-over threat?
    Would a trolling motor or 2 be adequate?
    With 2 you could steer by powering up the one on the outside of the turn, while diminishing power to the one on the inside of the turn.
     
  4. jklos2002
    Joined: Feb 2010
    Posts: 15
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: usa

    jklos2002 Junior Member

    don't know about wave-height rating - i doubt it was determined. Center of gravity is real low.

    It would be used on water with an extra set of 8 tires. I'm guesing the water level would be a few inches above wheel center, leaving 14" or so of free board. by my calculations, the 16 tires would support it even if completely swamped.

    good thought on the paired trolling motors. that may be the simplest route.
     

    Attached Files:

    • 3.jpg
      3.jpg
      File size:
      68.8 KB
      Views:
      700
  5. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    My concern is that once the tires lose contact with the bottom, the unit may lose stability. Have you had it in water deep enough for all tires to be suspended in water without any tire touching the bottom? If so, how did it behave?
     
  6. jklos2002
    Joined: Feb 2010
    Posts: 15
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: usa

    jklos2002 Junior Member

    I havent' had it in water. The sales brochure shows one out on a lake with 9 people piled in.

    Hull is flat bottomed (approx. 4'x8'), vertical sides, angled front & back.
     

    Attached Files:

  7. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    Test it. That photo does not tell you the water depth.
     
  8. jklos2002
    Joined: Feb 2010
    Posts: 15
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: usa

    jklos2002 Junior Member

    agreed, you can't tell the water depth from that photo. but, i've seen other photos of the machine being operated in greater depths.

    i'm a few weeks from testing in water. Thanks for your input!
     

  9. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    u r welcome
     
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.