Sliding Hatch

Discussion in 'Fiberglass and Composite Boat Building' started by fallguy, Sep 25, 2018.

  1. fallguy
    Joined: Dec 2016
    Posts: 7,596
    Likes: 1,674, Points: 123, Legacy Rep: 10
    Location: usa

    fallguy Senior Member

    I need to build a sliding hatch and want to make it out of 1/2" acrylic so it is more open down below.
    Walking on them possible, but not necessary and generally not done. Just don't want anyone falling through.

    I also would like to make the companionway door under the hatch acrylic and opens out. I figure the top of the slide can be the stop and a small cover will act as a seal for the top of the door.

    Dimensions of the door are about 24" high with a 20" width and the slide is going to be about 36" long and about 20" wide.

    I need to come up with a leakproof profile for the slides.

    I figure a garage is an absolute based on the long length. Length is needed as the drop into the hull is about 50"or so.

    rwatson had a couple of nice pictures, but no profile details

    I'd like to also make the slides of ptfe or Teflon.
     
  2. JamesG123
    Joined: Mar 2015
    Posts: 654
    Likes: 76, Points: 28, Legacy Rep: 10
    Location: Columbus, GA

    JamesG123 Senior Member

    Use UV resistant polycarbonate not acrylic (plexiglass). More expensive but it will last a lot longer, tougher, and easier to work with.
     
    fallguy likes this.
  3. fallguy
    Joined: Dec 2016
    Posts: 7,596
    Likes: 1,674, Points: 123, Legacy Rep: 10
    Location: usa

    fallguy Senior Member

    06B484B3-F6B6-4017-91FB-AD26E39DE32B.jpeg I drew up a section.

    Just not sure if the receiver and rail should be radiused ptfe or square. I could see where a radiused rail might be better and maybe leave the square guide.

    I'm a little unsure about clearances for the moving parts.
     
  4. JamesG123
    Joined: Mar 2015
    Posts: 654
    Likes: 76, Points: 28, Legacy Rep: 10
    Location: Columbus, GA

    JamesG123 Senior Member

    Should not matter as long as they are not binding. They are self-lubricating. So mostly its a matter of how good are you at making a square. Oh and I guess the thermal expansion coefficient. Find out what that is for the teflon and whatever poly you use and there you go.

    You will want to make the teak trim cover the entire receiver frame and screw into it. Otherwise it will look weird and you would see the ends of the screws in the clear poly.
     
  5. fallguy
    Joined: Dec 2016
    Posts: 7,596
    Likes: 1,674, Points: 123, Legacy Rep: 10
    Location: usa

    fallguy Senior Member

    Good point.

    I am also considering using linear bearings. They would roll nicer, maybe too nice?
     

  6. JamesG123
    Joined: Mar 2015
    Posts: 654
    Likes: 76, Points: 28, Legacy Rep: 10
    Location: Columbus, GA

    JamesG123 Senior Member

    Too nice. You would need a catch to keep the hatch from slamming back and forth in rollers. Plus they would eventually corrode/get clogged with gunk.
     
    fallguy likes this.
Loading...
Similar Threads
  1. socalspearit
    Replies:
    3
    Views:
    924
  2. cy fishburn
    Replies:
    5
    Views:
    1,883
  3. alby joy
    Replies:
    4
    Views:
    1,783
  4. Kazulin
    Replies:
    3
    Views:
    2,480
  5. midcap
    Replies:
    3
    Views:
    2,485
  6. Ctowles
    Replies:
    12
    Views:
    5,958
  7. hyboats
    Replies:
    3
    Views:
    2,497
  8. midnitmike
    Replies:
    14
    Views:
    50,991
  9. roseisland
    Replies:
    1
    Views:
    3,274
  10. hyboats
    Replies:
    2
    Views:
    4,103
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.