Innovations in Waterjet Technology

Discussion in 'Jet Drives' started by camglasgow, Feb 16, 2006.

  1. camglasgow
    Joined: Feb 2006
    Posts: 8
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: United Kingdom

    camglasgow Junior Member

    Hello all, this is my first post in what looks like a great forum & community.

    I’m a final year aeronautical engineering student at the University of Glasgow. My final year project is to propose and research design innovations for marine waterjet propulsion systems. So far I have looked into the viability of creating an electrically powered waterjet (to drive a cabin-cruiser type boat). The innovation part here is the integration of an electric motor in the waterjet duct so essentially it is a shaftless device, with the impeller ring acting as an armature.

    I was wondering if anything similar to this had been done before, and if anybody could point me in the direction of any helpful resources for electric waterjets?

    Thanks,
    Chris
     
  2. JonathanCole
    Joined: May 2005
    Posts: 446
    Likes: 10, Points: 18, Legacy Rep: 58
    Location: Hawaii

    JonathanCole imagineer

    Attached Files:

    1 person likes this.
  3. camglasgow
    Joined: Feb 2006
    Posts: 8
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: United Kingdom

    camglasgow Junior Member

    This seems to be along the same lines as I was thinking. How does the impeller ring rotate here?

    Cheers,
    Chris.
     
  4. john zimmerlee
    Joined: Apr 2006
    Posts: 36
    Likes: 2, Points: 0, Legacy Rep: 39
    Location: Atlanta GA

    john zimmerlee Junior Member

    Waterjet

    Can these be driven by 12V 30 amp motors?
    What's the smallest size?
    Are controllers available?

    John
     
  5. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    Would almost be tempted to wrap a permanent-magnet rotor around that impeller and place the whole thing inside a ring-shaped stator winding hooked up to one of Tritium's new WaveSculptor three-phase inverters... $$$$!
    I doubt it's in production yet, but it's an interesting concept. Would be neat to see what the performance curves end up looking like.
     
  6. Guillermo
    Joined: Mar 2005
    Posts: 3,644
    Likes: 189, Points: 63, Legacy Rep: 2247
    Location: Pontevedra, Spain

    Guillermo Ingeniero Naval

    Attached Files:

    1 person likes this.
  7. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    Quite an interesting little unit there, Guillermo. Intuitively, it does look like it should be more efficient than a conventional prop, since the stream is confined within the duct and cannot diffuse radially outwards like a conventional prop-wash does. I would hate to run aground with the thing, though!
     

  8. Guillermo
    Joined: Mar 2005
    Posts: 3,644
    Likes: 189, Points: 63, Legacy Rep: 2247
    Location: Pontevedra, Spain

    Guillermo Ingeniero Naval

    Well, the image is from a test boat and I think that for 'normal' uses we can locate the propeller in more or less the same place as they are now, only that we can avoid the rudder.
    I find this idea very eye-catching because it's an hybrid among a pod and a nozzeled propeller such as those used for fishing trawlers, but with the advantage of the electric rim power transmision, so avoiding gear, shaft and hub.
    Although in Brian Eiland's thread (http://boatdesign.net/forums/showthread.php?t=9432) Deering raised the concern about problems due to floating debris (ropes, logs and the like), I find it very interesting for fishing trawlers and tugs, if developers can come up to the powers needed. I have some doubts about the rim powering ability to handle let's say 4000 HP and keeping at the same time watertighteness (?).
    It's going to be interesting to follow further developments.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.