Epoxy Allergy - Suggestions on How to Finish a Boat?

Discussion in 'Fiberglass and Composite Boat Building' started by Chotu, Mar 11, 2018.

  1. pauloman
    Joined: Jun 2010
    Posts: 268
    Likes: 10, Points: 18, Legacy Rep: 151
    Location: New Hampshire

    pauloman Epoxy Vendor

    eventually you get reactions to all epoxies - that said I have had customers tell me they could still use my Basic No Blush epoxy but not the other 'big' brand epoxy often used.....
     
  2. fallguy
    Joined: Dec 2016
    Posts: 7,598
    Likes: 1,674, Points: 123, Legacy Rep: 10
    Location: usa

    fallguy Senior Member

    Not sure if it got mentioned, but I have vinegar all over my build area. I wash my hands with vinegar after glove removal.

    I have a half gallon vinegsr jug in my shower.

    It can be hard on the eyes, but I hate the odor of epoxy curing in my hair much worse.

    Also, why not try barrier creams? Unless you break out from inhalation; barrier cream and double gloves is very helpful.

    And we use a lot of paper toweling. It is just part of my messy operation.
     
  3. freddyj
    Joined: Oct 2013
    Posts: 287
    Likes: 23, Points: 18, Legacy Rep: 37
    Location: kansas

    freddyj Senior Member

    I became sensitive about half way into my build. After that I had to wear a full suit, double gloves, hood, and repirator just to mix small amounts. I also found out that the mixing ratios make a difference. I tried one with 100:16 ratio and it was much worse than the 100:25 I had been using. A noticeable difference. I didn't have a lung problem, but my arms, hands, and neck would break out terribly as soon as I got near the epoxy. After staying covered up for two years, now I can do small amounts without it bothering me, as long as I don't get it on my skin.
     

  4. sailhand
    Joined: Jan 2017
    Posts: 141
    Likes: 43, Points: 28, Legacy Rep: 29
    Location: australia

    sailhand Senior Member

    In Australia samples sent to the university of Southern Queensland for testing for a surveyed vessel (commercial vessel) using vinylester adhered to cured epoxy proved to be more than adequate. The only provisos was the use of a light, 200 m2, chop strand mat between the two laminates. The epoxy laminate was well cured before the vinylester was used for secondary bonding. All the usual surface prep rules obviously apply. The gougeon brothers also tested polyester resins bonded to cured epoxy with very promising results in contrast to popular opinion. I don't think I would try to use polyester to bond to epoxy however it is not uncommon in Australia to use vinylester on epoxy in surveyed vessels. Definitely worth a shot. I suffer from a severe allergy to epoxy also and I am not alone. I live on an epoxy built catamaran and my next repairs will be in vinylester. The local west system agents had testing done with similar results as they market a product called Duflex which is laminated with epoxy and some builders with epoxy allergies wanted to use the product. They were the initial source of my information. I would suggest testing vinylester for your project.
     
Loading...
Similar Threads
  1. Space
    Replies:
    2
    Views:
    29
  2. mrdebian
    Replies:
    11
    Views:
    566
  3. abosely
    Replies:
    8
    Views:
    1,197
  4. abosely
    Replies:
    4
    Views:
    732
  5. leaky
    Replies:
    19
    Views:
    1,973
  6. abosely
    Replies:
    6
    Views:
    745
  7. ahender
    Replies:
    3
    Views:
    678
  8. Klink Sanford
    Replies:
    29
    Views:
    2,476
  9. ajse
    Replies:
    2
    Views:
    855
  10. Robert Biegler
    Replies:
    6
    Views:
    1,723
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.