Deep V catamaran optimisation...

Discussion in 'Powerboats' started by CpDigriz, Apr 14, 2015.

  1. CpDigriz
    Joined: Apr 2015
    Posts: 16
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Scotland

    CpDigriz Junior Member

    I had dimensions for a deep v with chines, not sure yet about the dimensions for the rounder bottom
     
  2. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,045, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    This "project" is going nowhere, because you have not specified what you want, you say it is a race boat, but have not given the rules that govern the boats competing in the race. If they are open other than the 2x2x2.5 metres, I recommend an Acme Rocket Propelled Boat, as would be used by Wile E Coyote if there was any water out there in the desert.
     
  3. upchurchmr
    Joined: Feb 2011
    Posts: 3,287
    Likes: 259, Points: 83, Legacy Rep: 579
    Location: Ft. Worth, Tx, USA

    upchurchmr Senior Member

    You can't just have dimensions for a deep V - unless you know that will handle 250KG.

    When you are designing a boat, YOU have to figure out if it works.

    So far Wile E Coyote seems to be as good of a bet as anything.
     
  4. CpDigriz
    Joined: Apr 2015
    Posts: 16
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Scotland

    CpDigriz Junior Member

    I drew an autocad model and double checked with simple physics to see if it will stay up with that weight. .
     
  5. CpDigriz
    Joined: Apr 2015
    Posts: 16
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Scotland

    CpDigriz Junior Member

    And yet again with a very helpful recomendation, definitely the reason I came to these forums.
     
  6. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,045, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    Mate, if you cannot specify what it is you want, how do you expect to get it ?
     
  7. upchurchmr
    Joined: Feb 2011
    Posts: 3,287
    Likes: 259, Points: 83, Legacy Rep: 579
    Location: Ft. Worth, Tx, USA

    upchurchmr Senior Member

    Well now we get a little more information to know what is actually happening.
    Glad to see you did something.

    You appear to be ready to go. Autocad model, it floats.

    What materials have you choosen?
     
  8. CpDigriz
    Joined: Apr 2015
    Posts: 16
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Scotland

    CpDigriz Junior Member

    Carbon aramid + light and heavy glass layers.
     
  9. upchurchmr
    Joined: Feb 2011
    Posts: 3,287
    Likes: 259, Points: 83, Legacy Rep: 579
    Location: Ft. Worth, Tx, USA

    upchurchmr Senior Member

    I built an 11' catamaran rowboat with a sliding rigger for 50# out of strip cedar and glass.
    If you feel you have to use Carbon/ Aramid why would you want 2 different kinds of glass or even one kind?
    To use carbon effectively (minimum weight) you really need to know how to design a laminate, or you are going to waste your money.

    How long are you going to use this boat? One race?

    Wood and glass could probably get you a 70# hull and cross beams if you do it well (no big pools of epoxy and thin glass laminates).
    I'd suggest 1/4" strips of cedar and 4-6oz glass cloth inside and out. The cross beam might be smaller since you will not be sitting on it.
     
  10. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,045, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    The OP is employing a trickle-feed of information that isn't helping him or anyone else, put on the table what the purpose and reason of it all is, the whole box and dice.
     

  11. upchurchmr
    Joined: Feb 2011
    Posts: 3,287
    Likes: 259, Points: 83, Legacy Rep: 579
    Location: Ft. Worth, Tx, USA

    upchurchmr Senior Member

    Agreed, eventually I'll just stop responding.
    We have seen others do this. Seems like they don't really want any "help", they just want to see how many responses they can get. Sort of a weird personal best thing.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.