Epoxy over Polyester

Discussion in 'Fiberglass and Composite Boat Building' started by Blue Heron, Dec 5, 2005.

  1. Blue Heron
    Joined: Aug 2005
    Posts: 19
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Central Florida

    Blue Heron Junior Member

    Hi,
    I'm new to the forum and have a question. I'm planning a rebuilding project on a 17' seasquirt center console. I've had this thing for over 10 years, but the transom and deck have gone soft. I've never been really happy with the layout, so I want to start over rather than just repair the soft spots. I'm thinking of this project as kind of a short cut to a home built.

    I want to pull the console and inner liner out and start over from the bare hull. My intent is to lay up new foam core stringers, floors, and deck and then build foam core cooler, fish box, live wells, storage compartments, and forward and aft casting platforms.

    My first question is this. Is there any major prep work needed to bond epoxy resin to the old polyester lay-up other than roughing it up for good mechanical keying? In other words, are there any chemical bond incompatibility issues I need to mitigate?

    Thanks,
    Dave
     
  2. gasdok007
    Joined: Jul 2004
    Posts: 25
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: melbourne,fl

    gasdok007 Junior Member

    Make sure the existing glass is cleaned of contaminants,then key it with 80 grit or coarser. Epoxy will stick to existing polyester very well.New polyester won't adhere well to already cured stuff.
     
  3. glassman
    Joined: Nov 2004
    Posts: 36
    Likes: 2, Points: 0, Legacy Rep: 30
    Location: Toms River, N.J.

    glassman Junior Member

    there is one other way a lot less sanding have your parts sand blasted lite a good blaster can blast heavy like 36 gt or as light as 180 gt cost but saves time also it will find all that is bad
     
  4. Blue Heron
    Joined: Aug 2005
    Posts: 19
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Central Florida

    Blue Heron Junior Member

    Thanks for the info, guys. I read somewhere that polyester resin is sometimes used with additives (wax, for instance) and I was conerned that bonding could be affected. If sanding to break the surface and provide mechanical bonding is all that's required, that keeps it simple. Other than the obvious downside to sanding a lot of fiberglass, that is.

    Dave
     
  5. JR-Shine
    Joined: May 2004
    Posts: 341
    Likes: 4, Points: 18, Legacy Rep: 54
    Location: Vero Beach, FL

    JR-Shine SHINE

    wax can be from the fiberglass, or left over from the mold surface. You must get it off, and I would not rely only on sanding. If I were doing any work on FRP part (hull, deck, console, whatever) I would wipe the area down with a solvent (MEk or Acteone) then sand, then wipe it down again. It doesn’t take much wax or PVA to cause a bonding problem

    Joel
     
  6. SamSam
    Joined: Feb 2005
    Posts: 3,899
    Likes: 200, Points: 63, Legacy Rep: 971
    Location: Coastal Georgia

    SamSam Senior Member

    If you disassemble the boat this much make sure the hull is well supported and in the correct shape before you start and remains so until enough strength is built back in so it keeps its original designed shape. Sam
     

  7. Blue Heron
    Joined: Aug 2005
    Posts: 19
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Central Florida

    Blue Heron Junior Member

    Thanks. A guy I work with did the same with his boat and already offered the same advice. I'm planning to do just that.
    Dave
     
Loading...
Similar Threads
  1. Mark C. Schreiter
    Replies:
    18
    Views:
    4,159
  2. trekker
    Replies:
    23
    Views:
    3,574
  3. ssalmi
    Replies:
    6
    Views:
    3,186
  4. blink2u
    Replies:
    5
    Views:
    2,901
  5. brokensheer
    Replies:
    5
    Views:
    1,908
  6. mrdebian
    Replies:
    11
    Views:
    566
  7. abosely
    Replies:
    8
    Views:
    1,197
  8. abosely
    Replies:
    4
    Views:
    732
  9. leaky
    Replies:
    19
    Views:
    1,973
  10. abosely
    Replies:
    6
    Views:
    745
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.