sail area for a new design

Discussion in 'Boat Design' started by TimothyM, Dec 16, 2011.

  1. DCockey
    Joined: Oct 2009
    Posts: 5,229
    Likes: 634, Points: 113, Legacy Rep: 1485
    Location: Midcoast Maine

    DCockey Senior Member

    Take for example a simple plywood skiff, 14 ft LOA, 250 lbs rigged but without occupants. Put two 200 lb people sitting on the rail. They are the dominant contributor to maximum righting moment. Beam does matter in that case because if affects how far out they can fit.

    Actually, I find mixing the two approaches to generally be very productive. If they agree then it improves confidence. If they don't then further investigation may be worthwhile to determine if the engineering anaylysis is not sufficient, or if the "rule of thumb" is not applicable, or both.

    Any suggestions on a "rule of thumb" to use in determining mast scantlings for small boats? (SA/(LWL*BWL)) isn't directly relevant.

    The righting moment approach could be used with the simple approximations of the center of buoyancy located a half-beam from center, the CG of the boat on center, and without a trapeze or sliding seat the occupant weight a half-beam on the other side of center.
    Max righting moment = (weight of boat / 2 + weight of occupants) x max beam
    This would generally be a conservative over-estimate without a trapeze, etc nor a ballasted keel. Then for an unstayed rig the mast can be sized based on that moment applied at the deck/thwart/partners. If the rig is stayed the standard textbook type analysis can be done. In either case the sail area itself isn't needed, though with rigging the height of the "Center of Effort" may be needed to distribute the load.
     
    Last edited: Dec 20, 2011
  2. Petros
    Joined: Oct 2007
    Posts: 2,934
    Likes: 148, Points: 63, Legacy Rep: 1593
    Location: Arlington, WA-USA

    Petros Senior Member

    TimothyM,

    Ignore the "experts" and just go build it, what you have in terms of size of sail and mast will work out just fine.

    Boat building is as much guess work (based on the practical experience of similar designs) as it is an analytica design process. No one can perdict the maxium loads your particular boat will ever see, all we can is is guestimate on any of it.

    But as one of my engineering professors used to say: "one simple test is worth a 1000 expert opinions".

    Go build it and have fun with it. IF something breaks, build a stronger one to replace it.
     
    1 person likes this.
  3. TimothyM
    Joined: Jul 2010
    Posts: 74
    Likes: 2, Points: 0, Legacy Rep: 53
    Location: Maine

    TimothyM Junior Member

    Petros
    Thank you. that's my plan. I'm not reinventing anything here. I've based everything off of other boats. I just wanted to make sure I was in the ball park. I didn't want to be way under canvased. As far as the spars go, I'll build them on the safe side. I'll post pictures of the build later this winter.
     
  4. Perm Stress
    Joined: Sep 2009
    Posts: 554
    Likes: 24, Points: 0, Legacy Rep: 323
    Location: Lithuania

    Perm Stress Senior Member

    Sorry, did mix a two points a bit (sail area selection and sizing of rig).

    Take for example a simple plywood skiff,.....
    Yes it perfectly good approach to get good figures for further analysis or to add a healthy safety factor and build for them.

    Actually, I find mixing the two approaches to generally be very productive......

    I should have written "not very accurate". By writhing "not very productive" I had in mind "the result of such mixing is not accurate enough to engineer with stress 95 % of permissible :D, so further analysis is required"
     
  5. Perm Stress
    Joined: Sep 2009
    Posts: 554
    Likes: 24, Points: 0, Legacy Rep: 323
    Location: Lithuania

    Perm Stress Senior Member

    You are correct on "go on and build".
    Many the "experts" started this way, before becoming too lazy -calculations do not ask for so much sweat as actual building ;).
     
  6. TimothyM
    Joined: Jul 2010
    Posts: 74
    Likes: 2, Points: 0, Legacy Rep: 53
    Location: Maine

    TimothyM Junior Member

    just tought I'd show the finished product. I luanched her this summer. I ended up with a balanced lug about 135 sq.ft. She performed very well. Thank you all for your input.
     

    Attached Files:

  7. daiquiri
    Joined: May 2004
    Posts: 5,371
    Likes: 258, Points: 93, Legacy Rep: 3380
    Location: Italy (Garda Lake) and Croatia (Istria)

    daiquiri Engineering and Design

    That's a handsome boat, Tim. And the second pic looks just great! :)
     
  8. Petros
    Joined: Oct 2007
    Posts: 2,934
    Likes: 148, Points: 63, Legacy Rep: 1593
    Location: Arlington, WA-USA

    Petros Senior Member

    Congratulations! Very nice indeed.

    Thanks for sharing.
     
  9. TimothyM
    Joined: Jul 2010
    Posts: 74
    Likes: 2, Points: 0, Legacy Rep: 53
    Location: Maine

    TimothyM Junior Member


  10. FAST FRED
    Joined: Oct 2002
    Posts: 4,519
    Likes: 111, Points: 63, Legacy Rep: 1009
    Location: Conn in summers , Ortona FL in winter , with big d

    FAST FRED Senior Member

    Go big on sail, as was done 100 years ago.

    Pretty easy to shorten sail , sorta hard to lighten the boat for light airs.

    And a heck of a lot more fun to sail a powerful rig than a slug that takes 10K of breeze to answer the helm.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.