Black painted fibreglass?

Discussion in 'Fiberglass and Composite Boat Building' started by JordieS, Nov 10, 2011.

  1. Tim B
    Joined: Jan 2003
    Posts: 1,438
    Likes: 59, Points: 0, Legacy Rep: 841
    Location: Southern England

    Tim B Senior Member

    Visibility is another consideration. Black is very hard to see in poor light against a dark sea. This might not be a problem in normal operations, but it will dramatically change your odds in a rescue situation.

    As has been mentioned, heat is bad for the structural properties of composites in particular. You'll need substantially bigger structure if you intend to operate at higher temperatures. This means more weight.

    A little dark trim to highlight the features is fine, but don't go all-black.

    Tim B.
     
  2. sean-nós
    Joined: May 2010
    Posts: 157
    Likes: 30, Points: 0, Legacy Rep: 392
    Location: Dublin,Ireland

    sean-nós Senior Member

    My hands and wet paper, I like to feel it as I sand hence I have no fingerprints :D

    No gelcoat or clearcoat just paint. "toplac international"
     
    1 person likes this.
  3. JordieS
    Joined: Apr 2011
    Posts: 89
    Likes: 1, Points: 0, Legacy Rep: 26
    Location: Australia

    JordieS Junior Member

    Sean-nos I sent you a pm regarding my questions about your boat so we can get back to the question on this topic.
     
  4. JordieS
    Joined: Apr 2011
    Posts: 89
    Likes: 1, Points: 0, Legacy Rep: 26
    Location: Australia

    JordieS Junior Member

    How hot would a light grey/silver get?
     
  5. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    White roofs get as dirty as all heck in record time. Been there, not going back.
     
  6. troy2000
    Joined: Nov 2009
    Posts: 1,738
    Likes: 170, Points: 63, Legacy Rep: 2078
    Location: California

    troy2000 Senior Member

    You beat me to it. That quote was the first thing that crossed my mind when I started reading the thread...:D
     
  7. rxcomposite
    Joined: Jan 2005
    Posts: 2,752
    Likes: 608, Points: 113, Legacy Rep: 1110
    Location: Philippines

    rxcomposite Senior Member

    Here is something published by Martin Hollmann in "Modern Aircraft Design" Vol2.

    "For the same type of surface but painted white, a surface temperature of 125 degree Farenheit was measured for a 95 degree F day."

    Just don't paint your boat with a color that will reach the Heat Distortion Temperature of whatever resin you are using.
     

    Attached Files:

    1 person likes this.
  8. ondarvr
    Joined: Dec 2005
    Posts: 2,929
    Likes: 573, Points: 113, Legacy Rep: 506
    Location: Monroe WA

    ondarvr Senior Member

    Depending on the resins used and the care taken during the build, dark colors don't pose much of a problem. It can frequently create cosmetic problems with the wrong resin or poor workmanship though.

    The biggest problem is post curing of the part resulting in print from the fabric showing in the gel coat due to shrink and movement of the resin. This is most common in boats being built in the winter when the shop conditions aren't good, the temperatures are low during construction leaving a great deal of residual cure. These boats may never see temperatures higher than the mid 60s F until several months down the road when they are out in sun and can reach temperatures in the 180F range. The cosmetics are negatively affected but the physical properties may increase. Resin type and how well it was used has a great deal to do with the amount change in surface profile too.
     
  9. tunnels

    tunnels Previous Member

    Some where ,sometime ,Proffessional boat builder magazine had a story on the very subject of colours and amount of heat you could exspect on a loverly !!
    Was very interesting and the amount of heat was increadable .
    Cant speak for wood or other materials But glass i would never want to own a dark coloured boat (any dark colour )
    During the manufacture of glass boats there is always air entraped in the resin and glass.
    Its very nature resin produces gas from the chemical reaction between the catalyst and the promoting chemicals in the resin to make it all go hard so there are pockets within the lay up .
    Excessive Heat will cause these pockets to exspand and one day you will look at your nice pretty shiney black boat and wonder "what the hell" !! Where did those marks come from ??
    what caused them??
    Stupidity is the biggest cause of just about any problem !
    then workmanship , that accounts for 90 % plus of glassing problems
    lastly the product !! and thats usually directly related to the first two on the list .
    Have a nice day !:D


    Black is always associated with dead things or things that are dead so where do you fit in scheme of things ??
     
  10. JordieS
    Joined: Apr 2011
    Posts: 89
    Likes: 1, Points: 0, Legacy Rep: 26
    Location: Australia

    JordieS Junior Member

    You have to remember that black is an extremely cool colour, you will cruise past people and they will be thinking "Better stay back from him" hahahahahaha, James Bond had a black boat in "The World is not Enough". Best boat chase scene in that movie.
     
  11. tunnels

    tunnels Previous Member

    Sorry black in my book is not cool !! its dumb non thinking type colour !
    But i will say dark charcoal metalic with a touch of black pearl added is a nice colour But its just used for a back ground color to hi-light reds and yellows, blues , purples and greens and oranges . But not dead black !!:eek:
     
  12. MikeJohns
    Joined: Aug 2004
    Posts: 3,192
    Likes: 208, Points: 63, Legacy Rep: 2054
    Location: Australia

    MikeJohns Senior Member


    I was interested to hear a SAR talk recently where they said Black is surprisingly easy to see, but that white hulls make the SAR crews groan since they are so camouflaged in a rough sea. But the deck color is most important in an aerial search, or maybe the antifouling paint if it's lolling ;).

    But that aside the expansion coefficient for GRP is high and it's sensible to keep it as cool as possible it's a cause of outer skins disbonding from cooler cores and inner laminates and the heat softens the glue.
     

  13. Tim B
    Joined: Jan 2003
    Posts: 1,438
    Likes: 59, Points: 0, Legacy Rep: 841
    Location: Southern England

    Tim B Senior Member

    Depends on the conditions and time I guess, but I'm slightly surprised by that. You'd think that a black deck against a dark sea at night would be pretty hard to spot. White you'd think was easier, but against spray, might be a bit harder.

    Personally, I reckon that fluorescent orange on rudders and keels (at least for part of the span) is a good idea, but you rarely see it on non-ocean-racing yachts.

    Tim B.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.