Datsun Diesel drivetrain

Discussion in 'DIY Marinizing' started by sal's Dad, May 31, 2005.

  1. sal's Dad
    Joined: Apr 2005
    Posts: 109
    Likes: 7, Points: 0, Legacy Rep: 85
    Location: New England

    sal's Dad Atkin/Bolger fan

    I am planning to build an Atkin tunnel-stern boat. Scaled up a bit, I figure the design will require 40 hp or so. Aluminum hull.

    I like the looks and functionality of a boat in a museum near me - a 1930's lobsterboat, with Ford engine and transmission, hand-operated clutch lever. Not sure what was used for a thrust bearing. As I recall the differential povided power to a niggerhead (am I allowed to use a politically incorrect, but historically accurate term here?) on deck.

    A family member has a rusty Datsun Diesel pick-up truck, engine still in good shape, and would like to see it used in a boat project.

    I know I am nuts, but does it make any sense to pursue the idea of dropping engine and transmission into a boat?

    With the right prop, transmission could allow some gearing" - low gears for towing and maneuvering, 3rd for cruising, 4th for light load and flat water, high speed.

    Fresh-water cooled, using an integral keel-cooler, minimal electrics, maybe no fuel pump (a gravity feed "day tank") etc. CV joint from drive-shaft to prop-shaft, with some kind of thrust bearing. Presumably water-cooled exhaust would be quieter, but fishermen around here just use straight-pipe exhausts, and I hate holes in the hull...

    I know for a gasoline conversion, pretty much all the electrics would have to be replaced, but not sure about diesel.

    Thanks for any advice or suggestions, however absurd. And yes, I know it would be easier, safer, and "better" to spend $10K on a marine engine... But what would be the fun in that?
     
  2. Corpus Skipper
    Joined: Oct 2003
    Posts: 606
    Likes: 8, Points: 0, Legacy Rep: 173
    Location: Corpus Christi TX

    Corpus Skipper Hopeless Boataholic

    These are ILLEGAL!!! If you break a hose, all the fuel will drain to the bilge, and we know what can happen next.
    The starter and altenator would have to be ignition protected marine types.
    The transmission won't do you any good, shifting gears under load would surely destroy the drivetrain, and the prop has to be chosen for a given speed and load, so is only efficient at one reduction ratio anyway. Spin it too fast, it will cavitate, too slow and you're wasting fuel. Most automotive trannies have a final drive of 1:1, or overdrive of .75:1 (or somewhere in that neighborhood), which would overload the engine and burn it up in short order. Most diesels have 2:1 reduction or higher.
     
  3. sal's Dad
    Joined: Apr 2005
    Posts: 109
    Likes: 7, Points: 0, Legacy Rep: 85
    Location: New England

    sal's Dad Atkin/Bolger fan

    Thanks for your comments -
    That makes perfect sense - My experience with this system is in British Seagulls - very elegant and effective! Any leakage (and there was always some) went straight overboard.

    Again, makes sense. I wasn't sure if Diesels had different rules!

    I don't follow - isn't that what a clutch is for?

    Yes, I understand. But if a prop were selected for a gear ratio of 2:1 and "typical" loaded, choppy conditions -- and you sometimes run at say 60% displacement, in flat water, with no spouse to tell you to slow down -- isn't it possible that a gear ratio of say 1.5:1 would be an improvement?

    Likewise if towing (or in very rough condidtions), with the same prop, but at a speed of 5 knots, instead of 15, wouldn't a gear ratio of 3.5:1 be an improvement, instead of lugging the engine?
     

  4. FAST FRED
    Joined: Oct 2002
    Posts: 4,519
    Likes: 111, Points: 63, Legacy Rep: 1009
    Location: Conn in summers , Ortona FL in winter , with big d

    FAST FRED Senior Member

    "Likewise if towing (or in very rough condidtions), with the same prop, but at a speed of 5 knots, instead of 15, wouldn't a gear ratio of 3.5:1 be an improvement, instead of lugging the engine?"

    You can only absorb so much power from any sized diameter of propeller.

    If your setup for top or cruising speed a 25% change in tranny ratios will surly help to optomize that cruise or top speed.

    Going to 3.5 to 1 would only help reduce speeds for close manuvering.

    If the fuel tank is above the engine , the required top outlet (rather than bottom discharge will still alow the fuel to syphon out.

    Personally we prefer the gravity feed as any fuel leaking is EZ to see, an air leak is LOTS harder to find.

    FAST FRED
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.