Beaching with Sterndrive

Discussion in 'Sterndrives' started by fritzdfk, Jul 15, 2011.

  1. IMP-ish
    Joined: Jan 2011
    Posts: 389
    Likes: 9, Points: 18, Legacy Rep: 150
    Location: united states of america

    IMP-ish powerboater

    I've never had a volvo sterndrive, so maybe I should keep my mouth shut. But with mercs my other nagging worry would be having the bellows so exposed by resting the drive on the bottom in the full trailer up position. Depends on the seabed I suppose. And what the consequence of breaking down is where you are boating.
     
  2. yipster
    Joined: Oct 2002
    Posts: 3,486
    Likes: 97, Points: 58, Legacy Rep: 1148
    Location: netherlands

    yipster designer

  3. fritzdfk
    Joined: Jul 2004
    Posts: 45
    Likes: 2, Points: 8, Legacy Rep: 32
    Location: Alaska

    fritzdfk Junior Member

    thanks

    The drive is at it's highest, the top of the Volvo 280 drive hits a rubber bumper and can't go higher. The boat is on a swinging mooring, two anchors with the boat in the middle. The support legs is an interesting idea but that would put the boat's weight on two points, forward under the bow and on the legs aft, probably not a problem. Perhaps a weighted block with a V shaped wedge out of the top that I can lower into the water and secure under the transom.
     
  4. anthony goodson
    Joined: Mar 2007
    Posts: 451
    Likes: 19, Points: 18, Legacy Rep: 256
    Location: Dorset UK & Murcia Spain

    anthony goodson Senior Member

    I am not familiar with your climate ,but here it would be wise to consider that most boats are designed to drain rainwater aft.
     
  5. FAST FRED
    Joined: Oct 2002
    Posts: 4,519
    Likes: 111, Points: 63, Legacy Rep: 1009
    Location: Conn in summers , Ortona FL in winter , with big d

    FAST FRED Senior Member

    Some of the units have 2 heights ,

    One is for beaching , the second is higher and used to increase clearance for road travel.

    Read Da Book?

    Usually a second pump switch is used for the road setting.
     
  6. fritzdfk
    Joined: Jul 2004
    Posts: 45
    Likes: 2, Points: 8, Legacy Rep: 32
    Location: Alaska

    fritzdfk Junior Member

    The drive can't go any higher. The top of the drive hits a rubber bumper. I can raise the drive slightly higher and compress the bumper a little but I think that is bad for the hydraulics.

    As far as rain goes, yes it rains a lot here, Southeast Alaska. The boat of course would float twice a day and rainwater would be pumped out then.

    I don't understand why a system would be designed like this. Perhaps on my boat the transom assembly was placed too low? I'll have to look at that the next time the boat is on it's trailer. I would assume that the cavitation plate should be placed slightly below the hull? Is there a standard?
     
  7. Deering
    Joined: Feb 2005
    Posts: 481
    Likes: 25, Points: 18, Legacy Rep: 44
    Location: Juneau, Alaska

    Deering Senior Member

    How about installing a short beaching skeg on your hull, just deep enough to take the load off of your outdrive while at rest?

    Might need to reinforce the hull to handle the skeg load, and watch to make sure you don't create cavitation issues on the props, but I've done similar successfully.


     
  8. anthony goodson
    Joined: Mar 2007
    Posts: 451
    Likes: 19, Points: 18, Legacy Rep: 256
    Location: Dorset UK & Murcia Spain

    anthony goodson Senior Member

    Strictly speaking it's an anti ventilation plate and is normally slightly above the bottom of the transom.
     
  9. IMP-ish
    Joined: Jan 2011
    Posts: 389
    Likes: 9, Points: 18, Legacy Rep: 150
    Location: united states of america

    IMP-ish powerboater

    What is your hull shape fritz?
     
  10. fritzdfk
    Joined: Jul 2004
    Posts: 45
    Likes: 2, Points: 8, Legacy Rep: 32
    Location: Alaska

    fritzdfk Junior Member

    The boat is a 23' Clippercraft. The hull is shallow V planing type.
     

  11. yipster
    Joined: Oct 2002
    Posts: 3,486
    Likes: 97, Points: 58, Legacy Rep: 1148
    Location: netherlands

    yipster designer

    Sounds like a simple solution such a skeg Deering
    better a double skeg than also becouse sterndrive instal manuals want a unobstructed free meter bottom in front of the leg
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.