Curved surface on plug?

Discussion in 'Fiberglass and Composite Boat Building' started by Bill Brasky, Nov 19, 2010.

  1. Bill Brasky
    Joined: Jul 2010
    Posts: 12
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Sandusky

    Bill Brasky Junior Member

    What do you guys use for curved surfaces on your plug? It's a little too much radius to bend plywood. Small boat, 10' long. Is foam my only option, I'm building it by hand, and foam worries me I won't get it symmetrical. Thanks.
     
  2. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    On a plug there are a number of tricks,Thin plywood another is closely spaced battens that could have a shape sawed in them,another is bending plywood,then veneers (fir and the like),sheets of plastics and metals.
     
  3. tunnels

    tunnels Previous Member

    You can also make thin Fibreglass panels and use the same method is plywood Or find a shape that is what you are looking for and simply mould it and fit it to the plug ! Glass shapes and panels are real easy to make anything out of !!
    Thin glass can be cut with scissors and stapled and glued in place Then glassed over ,then your fillers !!. :) nothing is imposable:confused:
     
  4. Landlubber
    Joined: Jun 2007
    Posts: 2,640
    Likes: 125, Points: 0, Legacy Rep: 1802
    Location: Brisbane

    Landlubber Senior Member

    Bill...the thinner the ply the more that you can shape it, so use aviation ply if necessary, it is 5 ply and can start at about 2mm.....

    ....and as Tunnels says, just use sheet glass panels, you make them on a sheet of real glass, they are very easy to make.
     
  5. jiggerpro
    Joined: Sep 2007
    Posts: 179
    Likes: 8, Points: 18, Legacy Rep: 101
    Location: spain

    jiggerpro Senior Member

    use 40mm thick MDF strips very flexible and easy sanding look at what we made with it:
     

    Attached Files:

  6. jiggerpro
    Joined: Sep 2007
    Posts: 179
    Likes: 8, Points: 18, Legacy Rep: 101
    Location: spain

    jiggerpro Senior Member

    it was made from 12mmx4mm MDF strips
     

    Attached Files:

  7. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    This is being made with Fiberglass,Plywood,Bending Plywood,Putty and Duratec


    [​IMG]
     
  8. GG
    Joined: Jan 2008
    Posts: 190
    Likes: 4, Points: 0, Legacy Rep: -30
    Location: MICH

    GG offshore artie

    Steve , i always enjoy your pics and i wish i would have taken more over the years .
     
  9. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    Artie Thank you.
     
  10. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    You can carve wood or mold fiberglass. I think that using the same material for finishing is important so that when you laminate the mold on and it heat up, there will be less distorsion. Beware of epoxy finishes, they inhibit the cure of polyester. For symmetry, use templates.
     
  11. GG
    Joined: Jan 2008
    Posts: 190
    Likes: 4, Points: 0, Legacy Rep: -30
    Location: MICH

    GG offshore artie

    You are always welcome ........................ and did you make it to the worlds by chance ?
     
  12. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member


    No I had a Sport fisherman in the water apart and needed to close it up.
     
  13. Bill Brasky
    Joined: Jul 2010
    Posts: 12
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Sandusky

    Bill Brasky Junior Member

    I saw that a lot of people make cedar strip plugs using 1/4 x 3/4" strips. What is the reason for the cedar as opposed to, say, pine which is cheaper?
     
  14. Herman
    Joined: Oct 2004
    Posts: 1,618
    Likes: 94, Points: 48, Legacy Rep: 1240
    Location: The Netherlands

    Herman Senior Member

    Perhaps that it is free of knots. However, that would not hold me back using pine. WRC is horribly expensive over here.

    One of my cusomers built a motor boat out of pine instead of WRC, as he is allergic to that wood, and this boat still floats...
     

  15. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    There is nothing wrong with pine. It was one of the usual species for plug making on castings. I think that the more even grain of the pine is superior to cedar. It makes it much easier to get an even finish.
     
Loading...
Similar Threads
  1. andysailor
    Replies:
    24
    Views:
    2,559
  2. andysailor
    Replies:
    17
    Views:
    4,673
  3. andysailor
    Replies:
    5
    Views:
    1,822
  4. fallguy
    Replies:
    35
    Views:
    3,521
  5. midcap
    Replies:
    6
    Views:
    4,330
  6. benglish300
    Replies:
    31
    Views:
    7,682
  7. querulant
    Replies:
    19
    Views:
    6,072
  8. gcdoyle
    Replies:
    6
    Views:
    2,028
  9. srimes
    Replies:
    5
    Views:
    3,464
  10. hyboats
    Replies:
    10
    Views:
    2,564
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.