Been given a boat, what to do???

Discussion in 'Sailboats' started by rad..., Jun 17, 2010.

  1. rad...
    Joined: Jun 2009
    Posts: 9
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: lost at sea.

    rad... Junior Member

    Well, half a boat.

    Hi all, my Uncle has given me an unfinnished hull for a 30ft yacht. sounds great!!, but he does'nt have any plans for it, he had a naval achitect help him with lofting and setting up the stations, that was 20 years ago.
    Its made out of corex foam sandwich, and he has forgotten what resin he used. We live in a very dry climate so i'm guessing the fibreglass will be ok, i've done abit of boatbuilding so i think i have what it takes (apart from patience). I guess what i'd like to know is how do i work out all the tecnical stuff. like how strong i'll need to make the chainplates, how tall should the mast be. also the displacement, where the waterline is, the righting moment, hull speed, and goodness knows whatelse. i need to make the deck and cabin aswell so i'll need to work that out too. do i need to post up some photos of it to give you an idea?? its aprox 28ft loa at the moment but the stern is not finnished yet, so it may end up getting to 30ft loa. beam is 8ft (cant change that) it has a 3/4 length keel with aprox 1 ton of lead. just guessing but he thinks the draft is about 4ft 4" with a freeboard of about 3ft. i would like to raise the freeboard about 6"-8" though, would that have adverse affects???
    I've had thoughts of just finnishing it off the best i can, but then i have nightmares that it'll just sink when i go to launch it, or it'll ride way too low in the water, or it wont sail properly, or somthing catostrophic like that.
    Sorry about the long post but i'm pretty keen on boats and sailing and like they say, "never kick a gift horse in the mouth" besides, its the only forseeable way i'll ever own a boat.
    Thanks heaps for reading and any info that you care to share!!
    Cheers, rad...:)
     
  2. djwkd
    Joined: Jul 2006
    Posts: 380
    Likes: 2, Points: 18, Legacy Rep: 51
    Location: Newcastle-Upon-Tyne

    djwkd Senior Member

    Is it EXACTLY half a boat, or just 'nearly' half a boat?
     
  3. daiquiri
    Joined: May 2004
    Posts: 5,371
    Likes: 258, Points: 93, Legacy Rep: 3380
    Location: Italy (Garda Lake) and Croatia (Istria)

    daiquiri Engineering and Design

    How about hiring a surveyor who will evaluate the current state of the hull and will give you a few phone numbers of naval architects you could contact in your area?
     
  4. rad...
    Joined: Jun 2009
    Posts: 9
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: lost at sea.

    rad... Junior Member

    djwkd: Well, it probably is NEARLY EXACTLY half a boat, weight wise i'd imagine. work wise i'm sure i'm nowhere near half ;)
    daiquiri:
    Hey that sounds like a smart idea, getting a survey and a naval achitect and all that, only problem is we live 600klms inland :( i'll check it out though!! :)
    Thanks heaps guys, very much apreciated!!!! please keep the ideas coming!!
    Cheers!!!! rad...
     
  5. daiquiri
    Joined: May 2004
    Posts: 5,371
    Likes: 258, Points: 93, Legacy Rep: 3380
    Location: Italy (Garda Lake) and Croatia (Istria)

    daiquiri Engineering and Design

    That is not really a problem, in 21st century. ;)
     
  6. Typhoon
    Joined: Mar 2009
    Posts: 125
    Likes: 8, Points: 0, Legacy Rep: 150
    Location: Australia

    Typhoon Senior Member

    Just remember the old adage that something you are given for free is worth exactly what you paid for it......

    Regards, andrew.
     
  7. sorenfdk
    Joined: Feb 2002
    Posts: 511
    Likes: 27, Points: 28, Legacy Rep: 394
    Location: Denmark

    sorenfdk Yacht Designer

    Does your uncle remember the name of the NA? Maybe he'll be able to tell you more about the boat.
     
  8. Ike
    Joined: Apr 2006
    Posts: 2,677
    Likes: 476, Points: 83, Legacy Rep: 1669
    Location: Washington

    Ike Senior Member

    This is your only problem?


    If you are "lost at sea" how can you be 600 kms inland?

    I think you should hire an NA. He (or she) can take the lines off the hull, then design an interior and deck plan, and whatever else is needed. If you have photos someone here may recognize the design and be able to direct you to photos of a completed boat. Also If you can get the name of the NA someone here may know the person. NA's are a rather rare bred and there just aren't that many. So someone here probab;y knows him of of him.
     
  9. Munter
    Joined: Jul 2007
    Posts: 285
    Likes: 12, Points: 18, Legacy Rep: 125
    Location: Australia

    Munter Amateur

    I guess you need to think pretty soberly about how much work and cost you can expect to incur in finishing off the boat. If you're a long way inland perhaps you should also think about how much use you're going to get out of it and how practical it will actually be.
    Notwithstanding that the boat is "free", what will it actually cost to complete (be realistic, not optimistic with this) and are you happy to pay that amount and end up with an orphan design? Second hand boats are relatively cheap to purchase - you could potentially save money, time and effort buy buying a used boat in comparison to finishing off a half built one. Think carefully on this before proceeding and work out whether it is actually rational to complete the project.
     
  10. rad...
    Joined: Jun 2009
    Posts: 9
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: lost at sea.

    rad... Junior Member

    Thanks guys for your thoughts, no help yet on my first post, but all very good advise and very much apreciated.
    Ike, no its not my only problem, i have lots!! thats why i'm asking so many questions. about the lost at sea bit, well, i guess my mind is at sea somwhere wishing my body would join it sometime. lol!!!:D
    Being inland wont stop me sailing it down the river to the ocean, oh i forgot to mention that, sorry. :eek:
    I think i realize how much it will cost, i'm estimating around the $50,000 mark, although its more than likely to be more than that depending on how fancy i want to finnish it.
    The good thing about building a boat yourself is you know the quality of the workmanship, and how everything works, and you know that shortcuts hav'nt been taken. whereas if i bought a secondhand one i would'nt know what its like under the paint. about the orphan design, would that be a big deal:?: :?:
    Anyway, thanks heaps for all your valued oppinions, very much apreciated.
    Cheers! rad...
     
  11. Gilbert
    Joined: Aug 2004
    Posts: 525
    Likes: 5, Points: 28, Legacy Rep: 28
    Location: Cathlamet, WA

    Gilbert Senior Member

    Pictures Please.
     
  12. ancient kayaker
    Joined: Aug 2006
    Posts: 3,497
    Likes: 147, Points: 0, Legacy Rep: 2291
    Location: Alliston, Ontario, Canada

    ancient kayaker aka Terry Haines

    If you are serious then definitely post a few pictures and someone may recognize it or at least identify the generic type. At that point advice may be forthcoming, but recent discussions of the legal liabilities of boat designers has made many of our contributors nervous of volunteering opinions.

    There are some other points to consider:-

    Fiberglass left unprotected in the sun will deteriorate from UV.

    Finishing this boat will greatly exceed the cost to date of the partially complete hull. If cost is such an issue for you, also consider the marina costs for storing it hundreds of miles from home, security and maintenance, and traveling to it when you wish to enjoy it.

    If you are considering selling it once complete, be aware that builders also carry legal liability.

    Is this boat the one you actually want? The cost of a boat of half the length would be a small fraction of the cost of completing this one. A smaller boat might enable you to enjoy sailing on the river and give you far more satisfaction.

    If you cannot get plans for this design you may be wiser to sell the lead, scrap the boat and start on a new one, which can be the type, size and design that you actually want.
     
  13. anthonysudbury
    Joined: Jul 2010
    Posts: 2
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: United Kingdom

    anthonysudbury Anthony Sudbury

    Have you any pictures you could upload? Love to see what it looks like :)
     
  14. rad...
    Joined: Jun 2009
    Posts: 9
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: lost at sea.

    rad... Junior Member

    Hi again, sorry to take so long with some photos, technology is not my strong point. I've try'd to upload some photos, i hope they work, i dont know if they will help you determine what design it is though. but it might give you an idea of what i've got to work with and weather or not it will be worthwhile.
    (I think my uncle said it was a "galleon", a scottish design i think he said, but i searched the net and could'nt find anything.)
    So there you go, hope this helps somewhat.
    Thanyou for all the helpfull suggestions so far, cheers!!

    Rad...:)
     

    Attached Files:


  15. Submarine Tom

    Submarine Tom Previous Member

    That's not a boat.

    It is, however, a hell of a lot of work, money and design.

    Best of luck to you.

    -Tom
     
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.