gas problem

Discussion in 'Outboards' started by wordmaster, Jun 3, 2010.

  1. wordmaster
    Joined: Jun 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Georgia

    wordmaster New Member

    I have a pontoon with a 1982 Evinrude 90 hp motor. It has a 6 gallon metal tank under the back seat and a 12 gallon metal square shaped tank sitting on the back.

    The 6 gallon is easy to remove, just pick it up, but the 12 gallon is there to stay without some major rebuilding to get it back on.

    The motor will run fine, then start slowing down, missing, even die. You can change tanks and it will run fine again...for a while. I have replaced the gas hose and hose fittings, but no help.

    My best guess is that both tanks have some trash in them that, with the motor pulling, causes the strainer to stop up after a while. Without the motor pulling with sloshing around, it clears back up.

    What I need to know is what is the best way to clean the tanks. The 6 gallon of course has the lip inside so that simply rinsing and turning it upside down will not let the trash out. And, as mentioned, the 12 is more or less there to stay.

    Any and all help greatly appreciated.
     
  2. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    Beano. Oh, wait. Different kind of gas problem. Try siphoning off the gas, then fill it with water and siphon again, moving the siphon hose along the entire bottom of the tank, until you have cleared away as much debris as possible. Hook a shop vac to the fuel line and pull whatever remaining water out that way before refilling the tank. Try tilting the tank(whole hull if necessary) a few degrees to concentrate all the rubbish in one small area before siphoning.
     
  3. wordmaster
    Joined: Jun 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Georgia

    wordmaster New Member

    Thank you Hoyt...hope this works better than the beano did....
     
  4. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    He who masters words, masters the world.
     
  5. capt littlelegs
    Joined: Apr 2010
    Posts: 237
    Likes: 8, Points: 0, Legacy Rep: -67
    Location: England

    capt littlelegs New Member

    Check the tank air vents are open and the hose connections are good, could be pulling air.
     
  6. Bglad
    Joined: May 2010
    Posts: 175
    Likes: 5, Points: 18, Legacy Rep: 67
    Location: Jacksonville, Florida

    Bglad Senior Member

    Cleaning the tanks is a worthy cause but be very careful using a vacuum cleaner or any other electric appliance to clean it out you could turn it into a flame thrower or bomb!

    If the tanks are not above the powerhead you might try elevating the smaller tank to see if the motor performs better with fuel siphoning to it. You may have a worn out fuel pump. That might explain while it runs ok for a while after you switch tanks and pump the bulb. The full carburetors work until they begin running out of fuel.
     
  7. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    Which is exactly why you fill it with water first, to drive out any flammable liquids. Did you not read the post?
     
  8. wordmaster
    Joined: Jun 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Georgia

    wordmaster New Member

    Hopefully it is not a fuel pump. The motor may run good as long as an hour or as little as 10 minutes after changing tanks. Also, the large tank is above the motor.
     
  9. powerabout
    Joined: Nov 2007
    Posts: 2,944
    Likes: 67, Points: 48, Legacy Rep: 719
    Location: Melbourne/Singapore/Italy

    powerabout Senior Member

    Does the primer bulb start to go flat when the motor misses, can you squeeze it and does the motor recover?
    What happens if you press the choke while its dying?
     
  10. Bglad
    Joined: May 2010
    Posts: 175
    Likes: 5, Points: 18, Legacy Rep: 67
    Location: Jacksonville, Florida

    Bglad Senior Member

    Hoyt, I read fine even better with the big red letters. If gas remains in the fuel system the shop vac can be a hazard...
     
  11. wordmaster
    Joined: Jun 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: North Georgia

    wordmaster New Member

    Most of the time, the bulb goes flat or loses its hardness. Sometimes pressing the choke speeds it up. Sometimes, working the bulb makes it better, but usually not once it gets bad.
     
  12. hoytedow
    Joined: Sep 2009
    Posts: 5,857
    Likes: 400, Points: 93, Legacy Rep: 2489
    Location: Control Group

    hoytedow Carbon Based Life Form

    You are right. We must never assume the people reading the thread are competent enough to let some water dribble from the fuel line before hooking the shop vac to it in order to finish the desiccation process.:)
     
  13. CDK
    Joined: Aug 2007
    Posts: 3,324
    Likes: 148, Points: 63, Legacy Rep: 1819
    Location: Adriatic sea

    CDK retired engineer

    There is your answer!
    Run the engine with the filler cap removed. If OK, the vent is doesn't work, if not, the fuel line is clogged. Hoytedow told you how to proceed then.
     
  14. Submarine Tom

    Submarine Tom Previous Member

    OR, borrow another little, portable tank and try it.

    It might prove most enlightening...

    -Tom
     

  15. Ike
    Joined: Apr 2006
    Posts: 2,677
    Likes: 476, Points: 83, Legacy Rep: 1669
    Location: Washington

    Ike Senior Member

    Does it have an antisiphon valve at the outlet for the 12 gallon tank? Check and see if it's clogged. Also the springs in those things get old and they need to be replace. If the fuel line runs uphill to the engine you don't need it at all.

    Check to make sure vents are not clogged. Bugs like to build nests in vent lines.

    I would echo the comments about using a shopvac or any electric motor powered device. Be damn sure there is no gasoline vapor present or you will end up with a permanent sunburn.

    Tom's suggestion about borrowing another tank and trying it is excellent. It may not be the tank and fuel lines at all.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.