Deck-Hull Joint

Discussion in 'Fiberglass and Composite Boat Building' started by Dutch Peter, Aug 12, 2004.

  1. Dutch Peter
    Joined: Aug 2004
    Posts: 645
    Likes: 7, Points: 28, Legacy Rep: 66
    Location: The Netherlands

    Dutch Peter Senior Member

    Anyone ever did some calculations or tests on GRP deck joints which were only glued and not bolted or screwed?
    What's the general experience with this type of joints on the long run?
     
  2. mmd
    Joined: Mar 2002
    Posts: 378
    Likes: 16, Points: 0, Legacy Rep: 309
    Location: Bridgewater NS Canada

    mmd Senior Member

    I have no first-hand experience with controlled testing of non-mechanically fastened hull-to-deck joints, but I do know that several manufacturers of motor & sailing yachts are using advanced adhesives for structural bonding in these highly-stessed areas. I am currently telling several of my clients to use the "belt-and suspenders" method of bonding plus bolting mainly because their products (commercial fishing boats) take a lot of impact loading around wharves, and the conservative fishermen are reluctant to abandon the methods of construction that have worked for them in the past. Basically, no one wants to be the first to risk an expensive bond failure, and my client builders find the relatively small cost of adding bolts to the joint is easier than trying to change an industry mind-set. Personally, I would be in favour of a purely bonded seam in all but large or rough-useage vessels, provided that the shop practices and seam design were properly tuned for the adhesives.

    ITW Plexus, an American manufacturer, is very prominent in the US market, and I have spec'd their materials to clients for internal structural bonding. Their website is quite informative, and features some honest-to-god engineering data such as tensile strength, elongation, shear strength, etc.

    http://www.itwplexus.com/home.html
     
  3. Dutch Peter
    Joined: Aug 2004
    Posts: 645
    Likes: 7, Points: 28, Legacy Rep: 66
    Location: The Netherlands

    Dutch Peter Senior Member

    mmd,

    Quote: {Personally, I would be in favour of a purely bonded seam in all but large or rough-useage vessels, provided that the shop practices and seam design were properly tuned for the adhesives.} :)

    I agree with you, but have to work with a set of Rules. It is therefor I'm trying to find some data, to support my personal opinion.

    Local customer (sailing yachts 35-65 ft) has modified the bolt & adhesive methode. They're using countersunk bolts, no nuts, no washers, and a good adhesive. They cut thread in the flanges of the deck joint for the bolts. There is no laminate added afterwards to seal the joint.
    When testing this, the boltheads came of but the laminate remained undamaged.
    They're now thinking of leaving the bolts out completely.

    Does anyone know what the standard connection is according to for example:
    ABS, DNV, BV or GL? :?:
    Any other experiences with this type of joints. :?:
     
  4. Dutch Peter
    Joined: Aug 2004
    Posts: 645
    Likes: 7, Points: 28, Legacy Rep: 66
    Location: The Netherlands

    Dutch Peter Senior Member

    To keep my thread on top, I have to reply it myself. That's a laugh! :eek:
    I expected a bit more response, anyone????
     
  5. Danielsan
    Joined: Jul 2004
    Posts: 255
    Likes: 0, Points: 16, Legacy Rep: 10
    Location: Belgium (Europe)

    Danielsan Amateur designer-builder?

    Hi there,

    I am figuring out how to build my own boat at this moment so I have been doing some thinking:
    1 make a hull-deck-in-one seems difficult?
    2 get a male sleeve on the deck part, and get a female sleeve on the hull part
    before assembling fill the female sleeve up with a "Sikaflex' PU mastic(don't know if it's the wright word) NOT SILICONE!!! put the two pieces togheter. I did use it a lot
    in building joinery because of it's high dynamic strength.
    When used as a sort of glue it should just do great.

    Finaly you could glass over the joint,...

    Please correct me if I am wrong because I am willing to use it that way! :)

    Greetings,

    Daniel Peeters
     
  6. Dutch Peter
    Joined: Aug 2004
    Posts: 645
    Likes: 7, Points: 28, Legacy Rep: 66
    Location: The Netherlands

    Dutch Peter Senior Member

    In principal, your idea is not to bad, but make sure your sleeves are vertical otherwise it won't work.
    Your also right about overlaminating the joint, but that is just the point of my question. We don't want to do that anymore.
     
  7. Danielsan
    Joined: Jul 2004
    Posts: 255
    Likes: 0, Points: 16, Legacy Rep: 10
    Location: Belgium (Europe)

    Danielsan Amateur designer-builder?

    Yep that is one of my concerns at this moment, how am I going to make those sleeves?

    If you don't want to overlaminate the joint you don't need to, the joint will keep it together by itself. It should also give a nice cleen finish.

    Greetz,

    Daniel Peeters
     
  8. 4444xxt

    4444xxt Guest

    what's this than
     
  9. Roly
    Joined: Jul 2005
    Posts: 508
    Likes: 23, Points: 18, Legacy Rep: 222
    Location: NZ

    Roly Senior Member

    I am aware of the age of this thread....but
    Any updates on load testing a purely glued or filleted and tabbed hull deck junction?
    Anybody know of scantling rules for this type construction?
     
  10. SamSam
    Joined: Feb 2005
    Posts: 3,899
    Likes: 200, Points: 63, Legacy Rep: 971
    Location: Coastal Georgia

    SamSam Senior Member

    I imagine the people who sell the adhesive might know a little bit about it. Go here
    http://www.proboat.com/
    and page through their digital issues (page turning buttons at the top) and then go to their advertiser links and e=mail them.
    They might even have articles in the magazine itself.
     
    1 person likes this.
  11. Wynand N
    Joined: Oct 2004
    Posts: 1,260
    Likes: 148, Points: 73, Legacy Rep: 1806
    Location: South Africa

    Wynand N Retired Steelboatbuilder

    On our powerboats we join the deck to hull with bonding paste sold by Harvey's fibreglass. It has a grease like texture and activated with mekp. It forms a solid bond and never had deck came loose on our boats.
    Larger boats we fiberglass the fillet corner on the inside of joint over just to be on the safe side.
     
    1 person likes this.
  12. Roly
    Joined: Jul 2005
    Posts: 508
    Likes: 23, Points: 18, Legacy Rep: 222
    Location: NZ

    Roly Senior Member

    Thanks guys.
    I am more interested in the fillet & tab method but the adhesive Engineers probably know the numbers for this method as well.
    Also I will try the engineers at Hi modulus fabrics.
    I guess the weakest link is the secondary bond.
    It is too late for an overlap & adhesive/mechanical fixing for me.

    The NA's err on the side of accepted practice,(belt & suspenders approach) like most designers where the public is involved.
    Can't find anything in ABS either for purely F&T.
    Good to hear from your experience Wynand, thankyou.
     
  13. tunnels

    tunnels Previous Member

    While i worked in Korea last year making match racing yachts we did a nice detailed dech to hull joint i think you are looking for . This is my email address stuartwrcom@gmail.comand i will send you some pictures of what we had . The join was glued all the way round the boat and had no fastenings anywhere at all !! never had one problem with any part of the 8 boats , but i did increase the glueing surfaces from 40mm to 60 to get a little more from what we were doing . :p
     
  14. souljour2000
    Joined: Aug 2009
    Posts: 481
    Likes: 15, Points: 18, Legacy Rep: 195
    Location: SW Florida

    souljour2000 Senior Member

    My 83' hunter is glue-bonded at the seams only...looks like it is holding up okay but I am strongly considering adding bolts spaced a foot apart or a bit less..looking at adding a toe-rail...but I want to move the genoa track onto the cabin sides or top...out of the way..."the rat-walk" is skinny enough going forward on each side....the track is bolted heavily and is about 4 feet long...it would help the hull stay together in a de-lam situation...so thats also why I want to bolt the seam ....
     

  15. Speng
    Joined: Jun 2007
    Posts: 20
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: USA

    Speng Junior Member

    On a slightly different note, does anyone have experience with using structural adhesives in other parts of the boat such as bulkhead joints etc. I visited the SP factory on the Isle of Wight last year and they were using their Spabond product to do this type of thing. It's an epoxy product basically epoxy thickened with colloidal silica or something similar. They were using it on bulkhead joints on RNLI RIBS so it's evidently strong and their experience that it was at least as satisfactory as normal taped joints but much faster to apply.

    So anyone have experience with this or similar products or methacrylate glues in this application?
     
Loading...
Similar Threads
  1. farmerRob
    Replies:
    24
    Views:
    2,553
  2. bruceb
    Replies:
    10
    Views:
    1,570
  3. Cacciatore
    Replies:
    5
    Views:
    2,421
  4. Southern Cross
    Replies:
    23
    Views:
    8,519
  5. thorhawaii
    Replies:
    1
    Views:
    2,977
  6. Donavan C Marais
    Replies:
    12
    Views:
    2,701
  7. Clive Barry
    Replies:
    2
    Views:
    1,925
  8. hyboats
    Replies:
    30
    Views:
    26,901
  9. therigwelder
    Replies:
    15
    Views:
    6,806
  10. William Dion
    Replies:
    9
    Views:
    4,887
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.