Fuel Tank Placement

Discussion in 'Boat Design' started by dcrienks, Sep 7, 2009.

  1. dcrienks
    Joined: Sep 2009
    Posts: 2
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Basalt, CO

    dcrienks New Member

    I am restoring a 25' 1978 Starcraft Chieftain. It had twin I/Os. I took them out and I am installing a transome bracket with a 26" offset swimplatform to hold a single 250HP Yamaha four stroke outboard. The existing aluminum fuel tank is 60 gallons or so and is about 20" wide x 9" tall x 70" long and sits perpandicular to the centerline of the boat. I have decided to take it out and install a new plastic tank by Moeller. I plan to creat some storage where the I/Os used to be.

    So here are the questions,
    1. By moving the weight of the engine back behind the transom, is there a placement of the tank that will help in boat performance? Or do I just install the tank as far forward as I can?

    2. I was going to put in a 58 gallon belly tank to get the weight as low in the hull as possible, is this important?

    Thanks, Red
     
  2. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    Hi Red,

    I'm not sure what your original I/Os were, but I suspect the single outboard is a fair bit lighter than the two sterndrive engines were.

    Most likely, you want the boat's centre of gravity to be in roughly the same spot as it was before. At about 170 kg (370 lb), your fuel tank will have a pretty substantial effect on the CG. Depending on how the weight (and moment) of the new engine compares to the old ones, it may not be necessary to move the tank, or it may prove to be beneficial to move it forward. (Moving the tank too far forward, though, can cause trim issues when the tank is near empty- they're usually kept near the CG so that they don't change the boat's balance too much as they drain.)

    Have you done a weights-and-moments calculation yet? If you haven't, it's a worthwhile exercise to go through before finalizing the locations of too many heavy things.
     
  3. dcrienks
    Joined: Sep 2009
    Posts: 2
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Basalt, CO

    dcrienks New Member

    Additional information

    Thanks!

    The twin 4cyl I/Os and drives were about 1400 lbs. total

    The transom plates (to cover I/O holes), swim platform/motor mount, stringer supports, and the Yamaha is about 850 lbs total. Signficant weight reduction.

    Red
     

  4. Submarine Tom

    Submarine Tom Previous Member

    Red,

    I used to drive a commercial, 12 passenger I/O with Volvo-Penta's.

    They were removed, a two foot hull extension added and two, four-stroke

    outboards (Merc's) installed. The boat ran great BUT, in a sea that caused

    significant roll, the boat would "hang" when it rolled appreciably. It was

    most unsettling and disconcerting. I should add that no survey was done,

    no tank changes were made and no ballast added. I expressed my

    concerns to the owner and nothing was done. I left the company shortly

    there after. The boats (two) have both now been sold. My point is, I would

    heed the advice given thus far and exercise caution.

    Best of luck, Tom.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.