ask for help in maxsurf

Discussion in 'Software' started by chaser, Jun 16, 2009.

  1. chaser
    Joined: Jun 2009
    Posts: 27
    Likes: 1, Points: 0, Legacy Rep: 30
    Location: CHINA

    chaser Junior Member

    who can help me to fix this problem?
    Many thanks!
     

    Attached Files:

  2. gwboats
    Joined: Sep 2005
    Posts: 110
    Likes: 13, Points: 28, Legacy Rep: 77
    Location: UK

    gwboats Naval Architect

    Maxsurf Problem

    Chaser,

    This looks like a continuation of your previous posts - yes?

    I think if you need some help then you will have to attach some more information to your posting.
    You need to include the following:
    Hull definition file - e.g. problemship.msd
    Compartment definition file - e.g. problemship.htk
    Load case file - e.g problemship.hml
    Damage case - e.g problemship.dcs

    Also provide the specific criteria you are working to e.g MCA, USCG etc.

    Regards,
    Graham Westbrook
    Naval Architect
    www.westbrookmarine.co.uk
     
  3. chaser
    Joined: Jun 2009
    Posts: 27
    Likes: 1, Points: 0, Legacy Rep: 30
    Location: CHINA

    chaser Junior Member

    Gwboats,thank you for your reply,in fact it is very urgent for me,i need to fix the problem very soon,i have attached all the infors,please check it.Many thanks!
     

    Attached Files:

  4. gwboats
    Joined: Sep 2005
    Posts: 110
    Likes: 13, Points: 28, Legacy Rep: 77
    Location: UK

    gwboats Naval Architect

    Hydromax Problem

    chaser,

    Had a quick look at your files and the only number that is giving you problems is the port offset for the provisions (-0.874).
    Any value over about -0.7 is giving you the error you posted.
    Similarly if you change the heel and the downflood point to port for the stability analysis the error does not occur!
    I can only conclude that over -0.7 there is a hull definition clash, maybe this is something for you to check.

    Hope this helps.
    Graham Westbrook
    Naval Architect
    www.westbrookmarine.co.uk

    PS If I ever come to China you can buy me a beer.
     
  5. chaser
    Joined: Jun 2009
    Posts: 27
    Likes: 1, Points: 0, Legacy Rep: 30
    Location: CHINA

    chaser Junior Member

    Dear Graham:
    Thank you for your suggestion,i found the problem is deck eage in the stern,the postion is too lower,as i defined the stern part as a tank.wecome to china , i prepared several dozen of beer for you .
     
  6. chaser
    Joined: Jun 2009
    Posts: 27
    Likes: 1, Points: 0, Legacy Rep: 30
    Location: CHINA

    chaser Junior Member

    problem of maxsurf

    one more question ,i cant understand when i added spary rail on the original model,i found the sections aren't contious in the bow part.
     

    Attached Files:

  7. chaser
    Joined: Jun 2009
    Posts: 27
    Likes: 1, Points: 0, Legacy Rep: 30
    Location: CHINA

    chaser Junior Member

    Dear Graham:
    I am learning maxsurf right now ,i know you are very skill on it ,so i would like to ask you some questions,could you can help me,my email id is jack@iagyachts.com.
     
  8. gwboats
    Joined: Sep 2005
    Posts: 110
    Likes: 13, Points: 28, Legacy Rep: 77
    Location: UK

    gwboats Naval Architect

    Maxsurf Learning

    Chaser,

    As we say'Flattery will get you anywhere', however I don't think I have the spare time to help you consistently so my best advice is to take a training course in Maxsurf/Hydromax etc.

    I see from your e-mail address you work for a large yacht builder and I think you should approach them to buy you some formal training. After all it will be to the benefit of everyone!

    Good Luck
    Graham Westbrook
    Naval Architect
    www.westbrookmarine.co.uk
     
  9. chaser
    Joined: Jun 2009
    Posts: 27
    Likes: 1, Points: 0, Legacy Rep: 30
    Location: CHINA

    chaser Junior Member

    Dear Graham:
    Thank you for your honesty, i suppose it is the last question,i know you are very busy everyday,because i must to fix this problem today,i should send the final calculation to Rina, so i ask for help to you ,
     

    Attached Files:

  10. Andrew Mason
    Joined: Mar 2003
    Posts: 397
    Likes: 18, Points: 18, Legacy Rep: 206
    Location: Perth, Western Australia

    Andrew Mason Senior Member

    Chaser

    If you hav problems such as this it is best to contact Formsys support directly, they are experts and can sort out such problems very quickly.

    Contact email is support@formsys.com
     
  11. rohinit
    Joined: Sep 2009
    Posts: 3
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: india

    rohinit New Member

    I want to install maxsurf/S program from maxsurf formation CD (version 11) but it is asking for a password to extract the attached file.I have no idea where can I get this password from . Please Help
     

  12. zeroname
    Joined: Oct 2008
    Posts: 276
    Likes: 5, Points: 0, Legacy Rep: 90
    Location: Europe

    zeroname Naval Architect

    try this: exclam8ion
    if not work, contact the person from whom u got the CD or mail formsys.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.