A frame mast concept

Discussion in 'Sailboats' started by Norman Brown, Jan 19, 2009.

  1. Norman Brown
    Joined: Jan 2009
    Posts: 26
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Hartlepool, England

    Norman Brown Junior Member

    Amoco Procyon was a interesting experiment. But as a new concept was not the best or common sence answer for a 'A' frame mast system. The spars were not to correct beam theory so were over weight. On a correctly sparred system they would taper at both ends of each mast (windage down). No heavy system is neaded for chainplates for lower shrouds as they are gone. Lighter compression plates under the masts. No mast compression post (all weight !)The 'A' frame is scantled lighter as it is stiffer as 2 beems are cross joined. If you count it all up with loosing so much steel wire (sg. of 7.2). With a more efficient main I would like to know what's bad !?
    Norman
     
  2. tspeer
    Joined: Feb 2002
    Posts: 2,319
    Likes: 303, Points: 83, Legacy Rep: 1673
    Location: Port Gamble, Washington, USA

    tspeer Senior Member


    The main and jib help to reduce the drag of the mast. A Karman vortex street cannot form behind the mast because the sail acts like a splitter plate. The jib reduces the angle of attack of the mast, changing the apparent wind direction to coming more from ahead, and there can be a favorable pressure gradient toward the jib leech that helps to stabilize and reduce the lee-side separation bubble behind the mast. The rounded leading edge of the mast also provides a generous front-facing area for leading edge suction.

    The exposed A-frame mast gets none of these benefits. The mast legs are totally bluff bodies that get more of the full variation in apparent wind direction. The mainsail has a thin leading edge with very little area for leading edge suction. These factors more than make up for the reduction in windage from not having shrouds.
     
  3. alan white
    Joined: Mar 2007
    Posts: 3,730
    Likes: 123, Points: 0, Legacy Rep: 1404
    Location: maine

    alan white Senior Member

    I think the A frame has a chance with a rig where the main working plan is in the mains'l. The two shorter masts angle back enough to allow a vertical mains'l luff to backstay the jibstay.
    This allows the omission of any backstay to the stern. Now you can carry a full roach main on a foil gunter yard, so there's a clean leading edge all the way to the top.
    The two masts are now far shorter (about 33%, say) and the overall rig windage is improved, as the "center of parasitic drag" is far lower.
    If a rig like that performed well enough, it might well be the perfect rig for lowering in minutes for bridges, maintainence, or hauling.
     
  4. Norman Brown
    Joined: Jan 2009
    Posts: 26
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Hartlepool, England

    Norman Brown Junior Member

    A Frame mast continued

    Tom Speer's coment on the sail acting as a splitter plate behind the mast is right. But only part of the answer as vortice's are induced and do spoil the entry of the wind.
    The mast legs must be small foil shaped. Circular section will induce drag. Too large a foil and she will sail to windward and have problems in high winds. So correct calc's on the beams and shapes is critical.
    I have found a small article on a yacht called 'Kolika' Unfortunatly little info on her sailing capabilities. Does any one know more about this ?
    Norman Brown
     
  5. Squidly-Diddly
    Joined: Sep 2007
    Posts: 1,958
    Likes: 176, Points: 63, Legacy Rep: 304
    Location: SF bay

    Squidly-Diddly Senior Member

    got any pics of this A-frame?

    googling the name didn't bring up anything.
     
  6. Paul Scott
    Joined: Sep 2004
    Posts: 585
    Likes: 106, Points: 43, Legacy Rep: 84
    Location: San Juan Island, Washington

    Paul Scott Senior Member

    http://www.tspeer.com/landyachts/twin/top.jpg

    One direction the A frame idea could lead for sailboats, at least, would be something like Tom's sketch (link above), and designing the A frame for (say) 2 single foiled 3' chords for 20+ K, then use the 2 3' chords as wingmasts for fully battened mainsails (hoisted on them) for 8-20K, and then put a free flying jib in between them (in front of them?) for the light stuff, and a variety of (certainly interesting) downwind sails when needed. The tension for code zeroes might be a bit easier to achieve?
    Might be a bit of a nightmare at mooring, but hey, no pain, no gain...

    Paul
     
  7. Fanie
    Joined: Oct 2007
    Posts: 4,604
    Likes: 177, Points: 63, Legacy Rep: 2484
    Location: Colonial "Sick Africa"

    Fanie Fanie

    Look under aft mast.
     
  8. Norman Brown
    Joined: Jan 2009
    Posts: 26
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Hartlepool, England

    Norman Brown Junior Member

    For a look at a new type 'A'frame. (Double wishbone 'A' frame) Go to the boat design gallery and put. Lionhart. (Lionhart of Hartlepool). It takes some working out !
     
  9. gggGuest
    Joined: Feb 2005
    Posts: 865
    Likes: 38, Points: 28, Legacy Rep: 76
    Location: UK

    gggGuest ...

    Have you read Mikko Brummers CFD piece on rig behaviour here? You probably should.

    http://www.wb-sails.fi/news/Ad_aerodynamics

    It seems to me that the more we learn about what's going on the better a conventional round spar looks, and the advantage to be gained by using anything less conventional looks smaller and smaller. As a long standing enthusiast for the idea of using over-rotating wing masts I'm not entirely comfortable with this, but it does help explain why they've so rarely seemed to work as well in practice as I've thought they ought to.
     
  10. Paul Scott
    Joined: Sep 2004
    Posts: 585
    Likes: 106, Points: 43, Legacy Rep: 84
    Location: San Juan Island, Washington

    Paul Scott Senior Member

    I was obsessing about this a while ago- some stuff I found interesting

    "Reduction of fluid forces acting on a single circular cylinder and two circular cylinders by using tripping rods" Mahmbub, Sakamoto and Moriya

    "Flat plate drag reduction by turbulence manipulation" Narasimha and Sreenivasan

    "fluid mechanical issues of the flow around a bluff body" Akhilesh - this one is a power point presentation, so easiest

    Paul
     
  11. fishwics
    Joined: Mar 2004
    Posts: 33
    Likes: 1, Points: 8, Legacy Rep: 10
    Location: UK

    fishwics Quiet member

    URLs? or are they paper-only
    Cheers
    Simon
     
  12. Paul Scott
    Joined: Sep 2004
    Posts: 585
    Likes: 106, Points: 43, Legacy Rep: 84
    Location: San Juan Island, Washington

    Paul Scott Senior Member

     
  13. Paul Scott
    Joined: Sep 2004
    Posts: 585
    Likes: 106, Points: 43, Legacy Rep: 84
    Location: San Juan Island, Washington

    Paul Scott Senior Member

  14. Norman Brown
    Joined: Jan 2009
    Posts: 26
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Hartlepool, England

    Norman Brown Junior Member

    The unstable vortice's of a round body are avoided by having a egg or slight wing form set of masts. This drops the unstable element. Cross spars are made smaller and flatter. It has to be remembered that a standard rig has all the wire holding it up that has exactly this problem. Listen to the rigs of yachts in harbour during a strong wind, Oscilating. With a 'A' frame most of this is gone.:cool:
     

  15. Russell_Miller
    Joined: May 2009
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Rhode Island

    Russell_Miller New Member

    It'd be interesting to conduct the experiment again with a skin around the frame to help the aerodynamics out. When people home build carbon spars they'll build round sections (cause its easiest) and then add a better leading edge from a less expensive material that won't affect the spars bend characteristics.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.