Stainless Steel Question

Discussion in 'Sailboats' started by dreamer, May 2, 2005.

  1. dreamer
    Joined: Nov 2004
    Posts: 311
    Likes: 12, Points: 0, Legacy Rep: 188
    Location: Minnesota, USA

    dreamer Soñadora

    Hello Folks,

    (I also posted this on the Materials forum)

    I have a sailboat that I sail in freshwater with plans to someday take the boat offshore into saltwater. I recently inspected the chainplates and discovered a few of them were corroded. Fortunately I know someone who knows someone who was willing to fabricate a new set of chainplates from 304 ss for FREE. I would have preferred 316 ss but like I said...these were FREE!

    My question is what type of finish would be a good choice? Would it be adequate to simply polish these or would it be better to plate them? The chainplates are about 15" and 2" of the material extends above the deck. The deck seal consists of polysulfide with a ss trim plate on top of that.

    Thanks!

    Rick
     
  2. casavecchia
    Joined: Jan 2004
    Posts: 104
    Likes: 2, Points: 18, Legacy Rep: 14
    Location: Italy

    casavecchia Senior Member

    Go for 316!
    Marco.
     
  3. dreamer
    Joined: Nov 2004
    Posts: 311
    Likes: 12, Points: 0, Legacy Rep: 188
    Location: Minnesota, USA

    dreamer Soñadora

    I would love to...but 316 is not FREE. The 304 is FREE (meaning I would not have to pay any money...nothing...nada). So, since I am using 304, what would be the best way to finish it? Could I just leave it unfinished?

    Again, 316 is out of the question in this particular instance.
     
  4. woodboat
    Joined: Nov 2003
    Posts: 312
    Likes: 1, Points: 0, Legacy Rep: 14
    Location: Baltimore MD, USA

    woodboat Senior Member

  5. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    304 stainless is not designed for marine applications. If you must use it, treat it as you would a plain low-alloy steel; its properties are closer to plain steel in the marine environment.
     
  6. dreamer
    Joined: Nov 2004
    Posts: 311
    Likes: 12, Points: 0, Legacy Rep: 188
    Location: Minnesota, USA

    dreamer Soñadora

    Thanks guys.

    In fact, I actually contacted the folks at HG Houston. They suggested that I paint the chainplates with a marine grade epoxy paint.

    Also, is there a way to tell what type of stainless it is?
     
  7. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    Marine epoxy paints are used all the time on plain steel; they work just fine if applied right.
    You can't tell the exact grade number by looking at it. However, a fridge magnet is a good tool for guessing- the higher-quality the stainless steel, the less the magnet will stick to it. Tapping your magnet on a few known samples and then tapping it on your unknown one will give you a pretty good idea what grade it is.
     
  8. DSmith
    Joined: Dec 2004
    Posts: 53
    Likes: 2, Points: 0, Legacy Rep: 12
    Location: Sydney

    DSmith Junior Member

    Polishing

    The better the polish, the better the surface corrosion resistance.
     
  9. lenandval
    Joined: Dec 2009
    Posts: 5
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: UK

    lenandval Junior Member

    SS chainplates

    I had cause to weld an extension into a too short 304 aerial mast. The original had been electropolished and looked superb. The extension was welded to the base and was a section of the original construction metal but with the original linished finish. 19 years later the original remains untouched and unblemished while the extension requires seasonal cleaning to clean up the brown stains that a season at sea always produces. Electropolishing is an industrial process and is not cheap in the UK. It works beautifully.
     
  10. dreamer
    Joined: Nov 2004
    Posts: 311
    Likes: 12, Points: 0, Legacy Rep: 188
    Location: Minnesota, USA

    dreamer Soñadora

    That's interesting (especially considering this is a 4 year old thread! :))

    Wikipedia's entry doesn't say a whole lot. I would think all the acids used are pretty expensive.
     

  11. lenandval
    Joined: Dec 2009
    Posts: 5
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: UK

    lenandval Junior Member

    How did your preferred solution work out?
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.