Recent Content by yokebutt

  1. yokebutt
    Post

    off trailer & on to cradle ??

    Bubba-power
    Post by: yokebutt, Feb 18, 2007 in forum: Fiberglass and Composite Boat Building
  2. yokebutt
    Post

    Robber 3e design quarter tonner

    Robber, by Peter "Pink Panther" Ståhle was built concurrently with Accent at my dads shop in 73/74. Peter also designed a 73 footer for the first...
    Post by: yokebutt, Feb 15, 2007 in forum: Boat Design
  3. yokebutt
    Post

    which paring chisel or slick?

    Have a look at barrtools.com, reasonable prices, haven't bought anything there myself though.
    Post by: yokebutt, Feb 7, 2007 in forum: Wooden Boat Building and Restoration
  4. yokebutt
    Post

    epoxy sealing a brass carburetor float?

    I doubt the hardware store type foam would stand up to gasoline.
    Post by: yokebutt, Jan 24, 2007 in forum: Materials
  5. yokebutt
    Post

    Help needed for material

    Eric, Just to be a petulant arse, DB probably knitted rather than woven.
    Post by: yokebutt, Jan 19, 2007 in forum: Materials
  6. yokebutt
    Post

    Help needed for material

    Well... Ara- aramid? Mat- mat? 72k- fibers per yarn? 200- areal weight (g/m2)? 0˚/90˚- fiber orientation in fabric?
    Post by: yokebutt, Jan 19, 2007 in forum: Materials
  7. yokebutt
    Post

    classic Snipa

    Nå pråblem, mate.
    Post by: yokebutt, Jan 19, 2007 in forum: Wooden Boat Building and Restoration
  8. yokebutt
    Post

    awl grip or what?

    Awl-craft might be a little more forgiving to work with.
    Post by: yokebutt, Jan 16, 2007 in forum: Fiberglass and Composite Boat Building
  9. yokebutt
    Post

    classic Snipa

    Looks like a sidevalve (sidventil) gasoline motor. Don't know anything about it myself, but it looks like a very basic design, I would start by...
    Post by: yokebutt, Jan 16, 2007 in forum: Wooden Boat Building and Restoration
  10. yokebutt
    Post

    keel fairing

    Since the Laser 28 was designed by proper naval architects, there won't be much gain in a section different from what was designed for it. Some...
    Post by: yokebutt, Jan 16, 2007 in forum: Sailboats
  11. yokebutt
    Post

    Best “One_Off” building method using foamcore

    Fasten on sheets of foam onto the mold by screwing through the mold from the inside, use heat to bend the foam if neccessary. Laminate the...
    Post by: yokebutt, Jan 5, 2007 in forum: Materials
  12. yokebutt
    Post

    how do you get your designs in production..?

    Aditun, Go for medical doctors as investors, they are often arrogant enough to think they are gods gift to investing. (I'd say lawyers too, but...
    Post by: yokebutt, Dec 21, 2006 in forum: Boat Design
  13. yokebutt
    Post

    Underwater foils --- Center / Effort and Percent / Chord?

    What's the condition of your sails?
    Post by: yokebutt, Dec 21, 2006 in forum: Sailboats
  14. yokebutt
    Post

    Metric measurements/plans

    Unless you have a really crude metric ruler, I just don't see the problem.
    Post by: yokebutt, Dec 21, 2006 in forum: Boatbuilding
  15. yokebutt
    Post

    Fibrglassing question

    Andy, most rotomolded products are polyethylene, (often referred to by ungainly acronyms like HDPE and UHMWPE) wich is a great non-stick surface...
    Post by: yokebutt, Dec 21, 2006 in forum: Fiberglass and Composite Boat Building