Recent Content by judgegage

  1. judgegage
    Post

    Mercury 110 Help

    You will probably need to soak in a penetrate and tap on it with a piece of hard wood between the hammer and part. Unless there was a change in...
    Post by: judgegage, Aug 4, 2011 in forum: Outboards
  2. judgegage
    Post

    Need Help Please - will this hull handle the weather in Port Phillip bay?

    You know what I love about post like this? Looking on a map and seeing where people are at. Messa is right, there are alot of if's and I'll add...
    Post by: judgegage, Aug 3, 2011 in forum: Powerboats
  3. judgegage
    Post

    Mercury 110 Help

    You can still get parts from your local Mercury dealer. Has the engine been submerged? I ask that because of the rust and corrosion on the...
    Post by: judgegage, Aug 3, 2011 in forum: Outboards
  4. judgegage
    Post

    Slipway Winch

    This is from a website about vehicle recovery, it's very in depth and applies to winching and hoisting. Very good info....
    Post by: judgegage, Jul 31, 2011 in forum: Boat Design
  5. judgegage
    Post

    To paint or Not to paint that is the ?

    Cop-R-Tox is a penetrate and will penetrate better than most paints. As stated off the BLP information sheet: Recommended Film Thickness - This...
    Post by: judgegage, Jul 30, 2011 in forum: Boatbuilding
  6. judgegage
    Post

    To paint or Not to paint that is the ?

    Sorry EZ this was removed from above. A pontoon boat deck gets wet 2 ways, from spray and splash from the bottom or on top from washing,...
    Post by: judgegage, Jul 30, 2011 in forum: Boatbuilding
  7. judgegage
    Post

    To paint or Not to paint that is the ?

    EZ, let me confuse you more or it might just what you are looking for. COP-R-TOX, look at the link below....
    Post by: judgegage, Jul 30, 2011 in forum: Boatbuilding
  8. judgegage
    Post

    1999 mako wiring diagram

    Ok, Your outboards should come with wiring harnesses. The Harnesses will/should have connectors for instrumentation, start switches, neutral...
    Post by: judgegage, Jul 27, 2011 in forum: OnBoard Electronics & Controls
  9. judgegage
    Post

    1999 mako wiring diagram

    Hate to tell you, but there really isn't one. The boat came from the factory with the basics (like lights, bilge pump). The boat was then rigged...
    Post by: judgegage, Jul 27, 2011 in forum: OnBoard Electronics & Controls
  10. judgegage
    Post

    12' mini Eliminator pickle fork tunnel hull

    Hey dutch, take a look at this: http://www.yamaha-rebuild.com/brochure.pdf As long as the rest of the outboard is in good shape it would be a...
    Post by: judgegage, Jul 23, 2011 in forum: Outboards
  11. judgegage
    Post

    GM 3.8 litre v6 specifications

    DC, I looked at that Wiki page and was thinking about the 3.8/3800 I have worked on and 2 I've owned, I could not remember any of them having a...
    Post by: judgegage, Jul 23, 2011 in forum: Gas Engines
  12. judgegage
    Post

    25' Lynwood/Bertam

    I see alot of "Help identify my/this boat", Take a look at this link. http://www.uscgboating.org/recalls/mic1.aspx It's for recalls, but you can...
    Post by: judgegage, Jul 20, 2011 in forum: Powerboats
  13. judgegage
    Post

    GM 3.8 litre v6 specifications

    WOW...Holden...You Aussies with your Road Warrior jokes...JK. OZ, The dimension are hard to find. I'm with WP23 get the measurements you need...
    Post by: judgegage, Jul 12, 2011 in forum: Gas Engines
  14. judgegage
    Post

    sweet aluminum boat identification help

    I believe that is a Feather Craft. They were built in the 50s and 60s in Georgia. Take a look at this link: http://www.feathercraft.net/FCAbout.htm
    Post by: judgegage, Jul 12, 2011 in forum: Powerboats
  15. judgegage
    Post

    Light Trow hull?

    You probably will save or come out even. I know we didn't discuss it but you will want to use marine plywood. It's a little more expensive but it...
    Post by: judgegage, Jul 12, 2011 in forum: Sailboats