Propeller KA 4 70 Geometry

Discussion in 'Props' started by sURAJ, Jul 8, 2017.

  1. sURAJ
    Joined: Jul 2017
    Posts: 3
    Likes: 0, Points: 1
    Location: usa

    sURAJ New Member

    I am trying to generate CAD model of propeller KA 4 70 in solid works and then later on I am trying to validate open water characteristics of propeller with experimental results using CFD. But I am having some problem with geometry of KA 4 70 propeller.
    First of all I am creating 2D airfoil section and then I am using formulas in Carlton for converting it in 3 Dimensional geometry. I have below question.
    1. I have attached the screenshot of formulas in Carlton. Does these formulas required 2D airfoil section to follow some convention like leading edge should be at (0,0) and trailing edge at (-c,0) where c is chord length ? I have also attached 2D airfoil section. Which airfoil section shall I use for these formulas?

    2. Also, I have attached screenshot of Prop KA 4 70. As can be seen from the picture, generator line is not passing exactly through the center line of chord at each cylindrical section. But, I think that these formulas assumes that generator line and center line are coincident and hence has the term 0.5C in these formulas? How shall I consider this in these formula?

    Thank you in advance.
     

    Attached Files:

  2. jehardiman
    Joined: Aug 2004
    Posts: 3,762
    Likes: 1,152, Points: 113, Legacy Rep: 2040
    Location: Port Orchard, Washington, USA

    jehardiman Senior Member

    In the 1988 edition of PNA, read Vol II, Chapter 6, Section 6. Geometry of the Screw Propeller. The dashed line shown on the blade development is the line of maximum section, not the 50% cord (though it may be). Additionally, the sections shown have to be laid out on the helical generator line for your specific radius|pitch combination, see the chapter I listed.
     
    DogCavalry likes this.
  3. sURAJ
    Joined: Jul 2017
    Posts: 3
    Likes: 0, Points: 1
    Location: usa

    sURAJ New Member

    Thank you very much. I have gone through the material on propeller screw geometry that is given in PNA Vol II. But, the section does not talk about how to convert 2D section airfoil data in 3D propeller geometry. I am using formulas from Carlton to convert 2D section airfoil to 3D propeller geometry so that 2D airfoil will be laid out on generator line and at particular pitch angle. But I am not sure if these formulas can be directly used for all 2D airfoil or formulas needs to be changed based on airfoil section.
     
  4. jehardiman
    Joined: Aug 2004
    Posts: 3,762
    Likes: 1,152, Points: 113, Legacy Rep: 2040
    Location: Port Orchard, Washington, USA

    jehardiman Senior Member

    I see your question now. No, you can't just plug and chug based upon the assumption that c/2 is always on the skew line. As you can see from the KA 4 70 blade section drawing, the center of the section is independent of the skew. FIW, just do it in cylindrical coordinates, there is no need to develop the blade in x,y,z if you use a boring mill not a turret mill.
     
  5. Marcogen
    Joined: Oct 2017
    Posts: 2
    Likes: 0, Points: 1
    Location: Naples

    Marcogen New Member

    Hi everyone, like sURAJ I'm trying to create a 3D geometry for the Ka 4-70.
    I'm working in Matlab and for now I've imported in a script the coordinates from the same tables posted by sURAJ.
    After a little work on these coordinates I've obtained the results that you can see in the image below.
    Now I have some questions for you and I will be very grateful if you can help me.
    The points of x=0 in my riferiment system are on the "center line" but I don't understand what it really is.
    In this riferiment system the chord isn't horizontal and the origin isn't on the middle of the chord.

    Now I want to generate a 3D geometry by importing curves from points in Solidworks but i think I have to convert the coordinates, give to the section the pitch angle and wrap them on an helix, can someone help me ?

    The last question is about the thickness at the centre of shaft : I don't know how to use this information.
    Sorry but I'm completely new in this sector and I'have already read the carlton section and the PNA
    bladexyz.jpg
    Thank you in advance
    Marco
     
    Last edited: Nov 1, 2017
  6. sURAJ
    Joined: Jul 2017
    Posts: 3
    Likes: 0, Points: 1
    Location: usa

    sURAJ New Member

    You can refer to Carlton's chapter 3. It gives detail information and formulas for generating 3D propeller geometry from 2D airfoil section coordinates. You can refer to section 3.7 for the formulas.
     
  7. Marcogen
    Joined: Oct 2017
    Posts: 2
    Likes: 0, Points: 1
    Location: Naples

    Marcogen New Member

    Thank you very much I think I got the geometry
     

    Attached Files:

    Last edited: Nov 6, 2017
  8. Sahil Jawa
    Joined: Sep 2018
    Posts: 1
    Likes: 0, Points: 1
    Location: Chennai

    Sahil Jawa New Member

    can u tell me how to do to convert the coordinates, give to the section the pitch angle and wrap them on an helix, can someone help me ?
     
  9. Romale
    Joined: Dec 2018
    Posts: 4
    Likes: 0, Points: 1
    Location: Russia

    Romale New Member

    Could you tell where did you get pitch distribution along the radius?
     
  10. jehardiman
    Joined: Aug 2004
    Posts: 3,762
    Likes: 1,152, Points: 113, Legacy Rep: 2040
    Location: Port Orchard, Washington, USA

    jehardiman Senior Member

    Ka series wheels are made for nozzles and do not have changes in pitch radially like open water propellers (i.e. like B series). That is why the root is so shortened and thickened. FWIW, bi-directional Kaplan blades used in thrusters are designed in an entirely different shape and manner.
     
  11. Romale
    Joined: Dec 2018
    Posts: 4
    Likes: 0, Points: 1
    Location: Russia

    Romale New Member

    jehardiman, thank you for your reply, the pitch question is clear. Now I'm checking the geometry of sections by tables from Carlton. The reference line for face/back coordinates still not clear for me. I guess (in my picture) Yellow line - reference line for points A and B, distance A-Yellow line - coordinate for the back, B-Yellow line - for the face (in percentage of max. thickness of the section, in some distance from max thick. line - 20, 40, 60...). But when I try to check the shape and thickness close to leading edge the geometry is crashing. (the main idea to use picture of section in scale, then check it by table from Carlton)
     

    Attached Files:

    • 1.JPG
      1.JPG
      File size:
      57.8 KB
      Views:
      767
    • 2.jpg
      2.jpg
      File size:
      102.5 KB
      Views:
      810
  12. jehardiman
    Joined: Aug 2004
    Posts: 3,762
    Likes: 1,152, Points: 113, Legacy Rep: 2040
    Location: Port Orchard, Washington, USA

    jehardiman Senior Member

    You say the geometry is "crashing", why? Is it that you have a poor splining algorithm? Are you not accounting for nose radius? Remember the root fileting is a whole other issue. There is plenty of space to fair the back and face (though most likely the 0.2R LE is going to be buried in the root filet anyway). I think you might have to look at your table better as it shows the face LE 100% from max thickness as 33.33 but the back LE 90% from max thickness as only 27.40. Either the table is accounting for the root filet or there is an error in the table (noting 23.33 vice 33.33 would not be unrealistic).

    Realizing something is wrong and then fixing it are what makes an engineer, everything else is repetition that can be done by anybody.
     
  13. Romale
    Joined: Dec 2018
    Posts: 4
    Likes: 0, Points: 1
    Location: Russia

    Romale New Member

    You are right. "Crashing" - wrong word, I meant strange coordinates for face LE 100% - 33 / back LE 95% - 27,40. I did not account nose radius, now I'm checking how to do it correctly. Thank you.
     
  14. Romale
    Joined: Dec 2018
    Posts: 4
    Likes: 0, Points: 1
    Location: Russia

    Romale New Member

    jehardiman, could you explain something. I can't find any clear instruction about calculation of Nose/Tail radius. (Neither in Carlton nor in PNA (v2)). I attached table for counting radius of Kaplan blade sections, but drawing from this table doesn't match with drawing from coordinates table (Carlton, PNA).
    Em - max thickness of section, Yн - nose circle ordinate, dн - diameter of nose circle (the same for trailing edge (tail) Yx, dx)
     

    Attached Files:


  15. ascial
    Joined: Feb 2022
    Posts: 6
    Likes: 0, Points: 1
    Location: Sweden

    ascial Junior Member

    Hey everyone!

    I have a question about creating Ka4-70 profile:

    I am using openprop to create Ka-40 profiles but I dont understand how I can calculate some data.
    For example; I need c/D and t0/D ratios but I did not find anywhere. Could you please share me these datas?

    Thanks in advance.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.