Auto Seal Coat as Anti UV for Carbon Spar

Discussion in 'Boat Design' started by BobBill, Nov 18, 2015.

  1. BobBill
    Joined: Oct 2009
    Posts: 873
    Likes: 25, Points: 28, Legacy Rep: 157
    Location: Minnesotan wakes up daily, in SE MN, a good start,

    BobBill Senior Member

    The idea of using auto seal coat to form a UV barrier on carbon spar was noted elsewhere.

    Sounded like good idea, any comments?
     
  2. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    Do you mean undercoating?
     
  3. philSweet
    Joined: May 2008
    Posts: 2,682
    Likes: 451, Points: 83, Legacy Rep: 1082
    Location: Beaufort, SC and H'ville, NC

    philSweet Senior Member

    I think he means clear coat.
     
  4. BobBill
    Joined: Oct 2009
    Posts: 873
    Likes: 25, Points: 28, Legacy Rep: 157
    Location: Minnesotan wakes up daily, in SE MN, a good start,

    BobBill Senior Member

    Aye! Clear coat it is. Had a brain fart. Sorry!

    I was going to use the two part stuff recommended by some to coat some AL T6 spars and actually painted the carbon boom and yard, but then read the comment about clear coat, and wondered how I never thought of it...and me being ex GM...Duh!

    Works for cars, must be perfect to protect against UV and sealing AL etc.

    Ya think?
     
  5. messabout
    Joined: Jan 2006
    Posts: 3,367
    Likes: 510, Points: 113, Legacy Rep: 1279
    Location: Lakeland Fl USA

    messabout Senior Member

    Clear coats of all sorts have anti UV components but so far they are no match for pigmented coatings that exclude far more UV penetration. It is well known that the best possible varnish(clear coat) is paint.
     
  6. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    :confused: What does that last sentence mean ?
     
  7. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    Yep, that's right, the best UV protection is paint, with clear coats (regardless of type) being much lower on the UV protection list.
     
  8. Jim Caldwell
    Joined: Aug 2013
    Posts: 267
    Likes: 8, Points: 18, Legacy Rep: 48
    Location: Cleveland, Ohio

    Jim Caldwell Senior Member

    It used to be you could only get 3% UV inhibitors in Clear because it made the Clear cloudy. Of course that was 20 years ago, maybe that has improve some what, but you can see the nature of the problem.
     
  9. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    That's always been the problem Jim and though the new clear coats are better, they still have limited effectiveness, so automotive base coats have a lot of UV inhibitors in it as well..
     
  10. BobBill
    Joined: Oct 2009
    Posts: 873
    Likes: 25, Points: 28, Legacy Rep: 157
    Location: Minnesotan wakes up daily, in SE MN, a good start,

    BobBill Senior Member

    So, the best avenue would be to paint the carbon/epoxy to gain a few more years or so before having to redo. Makes good sense to me and I feel better for having painted the spars already.

    Appreciate the wisdom. The clear coat idea did seem viable alternative, when I came across it.

    Nothing beats experienced wisdom!
     
  11. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    I believe your geographic location would be a big factor in whether a clear coat would stand up, in some latitudes and climes it would last, others not so much. But why would you clear coat the item in question, rather than paint with a pigmented finish ? Many of the clear timber finishes I see on sale over here, promoted as suitable for exterior use, originate in Scandinavia, which is home to many red-heads who burn to a crisp in the climate here, much like the clear coat !
     
  12. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    Most want to see the carbon fiber and lots of automotive accessories are exposed carbon, so "it must be possible". A high latitude will delay the eventual UV damage, though it's still going to happen.

    I can do a pretty good faux carbon fiber look with painting techniques, which is a better way, in terms of durability.
     
  13. Mr Efficiency
    Joined: Oct 2010
    Posts: 10,386
    Likes: 1,042, Points: 113, Legacy Rep: 702
    Location: Australia

    Mr Efficiency Senior Member

    Yes, it dawned on me late that it was a cosmetic motive to use clear. :D The roads are full of mobile test-beds for clear auto finishes, so it must be doing OK, at least.
     

  14. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    Again, the base/clearcoat automotive systems incorporate UV inhibitors in both.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.