Decking - alternatives to teak

Discussion in 'Boatbuilding' started by Theodora, Jun 29, 2006.

  1. Theodora
    Joined: Jun 2006
    Posts: 14
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: brisbane & singapore

    Theodora Junior Member

    I want to plank over a marine ply deck with a durable wood. In a Florida climate, teak can get very hot under the bare foot due to its oils. An alternative is to use MarineDeck2000, an agglomerated cork product that looks good. However, I would prefer to use a wood that does not heat up so much as teak.
    Any naval architects or builders have any suggestions for this duty?:confused:
     
  2. waikikin
    Joined: Jan 2006
    Posts: 2,440
    Likes: 179, Points: 73, Legacy Rep: 871
    Location: Australia

    waikikin Senior Member

    White beech makes a nice light coloured deck. Regards from Jeff.
     
  3. FAST FRED
    Joined: Oct 2002
    Posts: 4,519
    Likes: 111, Points: 63, Legacy Rep: 1009
    Location: Conn in summers , Ortona FL in winter , with big d

    FAST FRED Senior Member

    While it doesnt have the Pinashe of wood we have used the moulded no skid look often.

    Simply get some heavy cotton mosquito net and cut ,trim till you get pleasing coverage.
    Outline the area with a light pencil and roll on a thin layer of 2part EPOXY paint.
    Lay the cotton on and roll on another layer of epoxy.

    Have no idea of the physics byt the cotton absorbes the epoxy accentuating the surface.

    Looks sorta like the sole of a Boston Whaler when done , fast cheap & repairable.

    And as hot as the color you chose to walk on.

    FAST FRED
     
  4. Theodora
    Joined: Jun 2006
    Posts: 14
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: brisbane & singapore

    Theodora Junior Member

    Jeff,
    Do you know anyone with White Beech deck experience I can talk to?
    John
     
  5. waikikin
    Joined: Jan 2006
    Posts: 2,440
    Likes: 179, Points: 73, Legacy Rep: 871
    Location: Australia

    waikikin Senior Member

    John, Ive laid a fair bit of teak & a few jobs in beech,the beech is nice to work & should be cheaper material wise- adhesive & seam compound will be the same though. generally a little softer than teak so you could go a bit thicker for wear.Glued it with sika with their primer or with international epiglue- precote of everdure seemed to promote adhesion on test pieces.I saw a beautiful example of white beech used on a Cole 46 "Wood wind" built in the 80's where it was combined with teak margin boards- absolutly fabulous to see. You can get it through maybe Caporns or Trend timbers or Anagote timbers in Sydney , dont know about the Singapore availability but I think it comes from the Solomon Is. mostly.Regards from Jeff.
     
  6. Theodora
    Joined: Jun 2006
    Posts: 14
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: brisbane & singapore

    Theodora Junior Member

    Jeff,
    Thanks for the recommendation. I am wondering how it weathers - does it go silvery like teak or does it retain it colour? Also, is it a wood that's prone to shrinkage, letting water down between it and the underlying marine ply?
    The most important point for me is whether it gets as hot as teak underfoot - do you have an idea about that?
    I'm building in NZ so I would expect it will be readily available there, but I'll give the timber suppliers you've mentioned a call.
     
  7. waikikin
    Joined: Jan 2006
    Posts: 2,440
    Likes: 179, Points: 73, Legacy Rep: 871
    Location: Australia

    waikikin Senior Member

    It goes silvery if left unoiled- brighter & lighter & more consistant in silveryness? than teak, under oil its a light yellow colour.If sawn & dried correctly it should hold up on seams good- definatly use seam tape & the correct primer for the seam compound.One job I worked on was a architectural "nautical aesthetic" where the material was supplied "on price" by a house builder- wide boards-slash sawn-not good, we did it, it looked ok on the patio but I wouldnt have put that style of material on a boat. Best to go narrow boards(45) & Quarter sawn for any overlay decking job.We dont generally lay stait onto ply- usually dynel over ply or to glass.The guy that did the Cole 46 "woodwind" was a Kiwi, Ian Gillies I think, havnt seen him for a long time maybe he's back over there, if not theres plenty of NZ boatbuilders to give you some tutoring on it. Regards from Jeff.
     
  8. Vega
    Joined: Apr 2005
    Posts: 1,606
    Likes: 26, Points: 58, Legacy Rep: 132
    Location: Portugal

    Vega Senior Member

    Are you sure that it would be different with other wood? With pinewood the deck can also get uncomfortably hot under the Med sun. (I know what you mean, its stupid to have to put your shoes on to go to the deck:p )
     
  9. harhhnt
    Joined: Oct 2006
    Posts: 40
    Likes: 2, Points: 8, Legacy Rep: 22
    Location: glen cove long island new york

    harhhnt Junior Member

    Anyone wanting to know about cork decks? Contact Marine-Solutions.com
    or e mail harhhnt@aol.com. We have been isntalling cork decks for 7 years and can give advice, sell you cork, install your deck, make a deck from a pattern. Best of all you will get real information from some one who really knows. Harry Hunt
     
  10. randyfraser
    Joined: Oct 2015
    Posts: 1
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: SoCal

    randyfraser New Member

    If one of the main things you want is minimal heat retention, cork is absolutely the way to go. Not to mention it's sustainably harvested, reasonably priced, easy to maintain and install. We went with cork on our transom steps a few years back and have since replaced the sole in the saloon and companionway steps. It's perfect. Check out more on cork decks at SeaCork: https://seacorkfloor.com/
     
  11. whitepointer23

    whitepointer23 Previous Member

    The op has probably chosen a material seems the thread is from 2006. :D
     
  12. whitepointer23

    whitepointer23 Previous Member

    Are you related to mike hunt.
     

  13. harhhnt
    Joined: Oct 2006
    Posts: 40
    Likes: 2, Points: 8, Legacy Rep: 22
    Location: glen cove long island new york

    harhhnt Junior Member

    Any one who would like to know about cork decking, is been 10 years since I posted here about cork, been working with this material for 20. Its nice to see some positive comments. I can be reached at harhhnt@aol.com or through my web site www.Marine-solutions.com

    AKA Mike Hunt
    Most people call me Harry
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.