Looking for a good filler/fairing compound for repairs

Discussion in 'Materials' started by gtcway, Feb 4, 2015.

  1. gtcway
    Joined: Dec 2004
    Posts: 7
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Bahamas

    gtcway Junior Member

    I do a bit of boat repairs involving gelcoat. I also paint boats with Awlgrip and always use epoxy fillers when painting.
    When it comes to gelcoat repairs, it depends on the location and customer but I use anything from 3m premium marine filler (expensive), auto lightweight filler (don't like to), to homemade fillers using polyester resin, microballoons and cabosil.
    I would like to be more consistent with using a better quality filler. Does it make sense to make homemade with vinylester resin? If so, is there any way to do it with a cream hardener for faster cure time and easier mixing of hardener?
     
  2. pescaloco
    Joined: Feb 2006
    Posts: 301
    Likes: 10, Points: 18, Legacy Rep: 81
    Location: so. california

    pescaloco Senior Member

    I like the 3M Vinylester filler for gelcoat repairs
    Yes it's expensive but you can't beat the BPO hardener for speed of cure
    For big stuff I mix balloons / cabosil AND talc for fairing putty
    You could also check out RJ fairing putty for a good premixed one MEKP catalyized

    Maybe some one will pipe in but I have never heard of BPO cream hardener being used with a regular poly/Vinylester laminating resin
     
  3. gtcway
    Joined: Dec 2004
    Posts: 7
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Bahamas

    gtcway Junior Member

    Is talc okay to use below the waterline?

    As for the cream hardener, it was just an idea I had to make it easier when mixing my own fairing compound. I guess I can catalyze before adding the fillers, but thought it would be a real time saver to premix larger quantities of fairing compound to use as needed. As everyone knows, it's much easier to know you're thoroughly mixing cream hardener with a thick paste vs. a small amount of clear liquid.
     
  4. FishStretcher
    Joined: Oct 2011
    Posts: 93
    Likes: 4, Points: 0, Legacy Rep: 33
    Location: On the Water

    FishStretcher Junior Member

    My experience with making my own vinylester fairing compound is that fresh resin has a shelf life of 3 months. If I have fresh resin, I can have a 10-20 minute pot life at 85F and 1.5% MEKP. This starting with a very thin" infuison grade resin. I spend the first 8 minutes or so mixing in the fumed silica and microballoons, after catalyzing the batch and this works well. Getting enough silica mixed in well enough, fast enough is a challenge for a larger batch. I do seem to err on too little silica and too much microballoons, typically. I wonder if one could premix the silica in the resin prior to catalyzation.

    I haven't tried the 3M product, but want to.

    I see you are in the Bahamas. I wonder if keeping the very reactive vinylester fresh is part of what drives your experiences? I store mine at 55-60F in the dark corner of a basement, and it is a very fast resin. I generally have too little pot life, not too much.
     

  5. gtcway
    Joined: Dec 2004
    Posts: 7
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Bahamas

    gtcway Junior Member

    I wouldn't mind premixing my own with polyester resin on some jobs, if there was a way to have it harden using cream hardener.
    I've never used vinylester resin for laminating. It's not available here, probably because it sets so fast. I only use polyester or epoxy.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.