Copper nickel

Discussion in 'Metal Boat Building' started by alanrockwood, Apr 19, 2011.

  1. alanrockwood
    Joined: Jun 2009
    Posts: 133
    Likes: 17, Points: 18, Legacy Rep: 116
    Location: USA

    alanrockwood Senior Member

    Could we discuss copper-nickel as a material for boat building?

    I realize the material is too expensive to be practical, but what if I were to win the lottery so that money is not much of an object. in that case what would one want to consider with respect to design and construction and operation of a ship made of copper-nickel alloy?

    One particular question (assuming that money is an object) how much more does this material cost these days than mild steel, and what are names of suppliers?

    By the way, Gerr's book has information on scantling rules for copper-nickel boats.
     
  2. alanrockwood
    Joined: Jun 2009
    Posts: 133
    Likes: 17, Points: 18, Legacy Rep: 116
    Location: USA

    alanrockwood Senior Member

    I today I talked to a seller of copper nickel. In very rough terms, copper nickel plate costs something like $10 per pound for 90/10 alloy (90% copper) and $13 per pound for 70/30 alloy (70% copper) plus shipping. A "mill order" is less expensive, saving around $2 per pound.
     
  3. Dean Smith

    Dean Smith Previous Member

    alloys of copper CUPRO NICKEL have been around a long time
    Used mainly in coolers now
    merriman bronze , alloy of cu ni and other stuff is immensily strong in tensile
    To answer your question
    You could build a yacht with a bronze cooper alloy the strength is absolutely astonishing I saw a Rhodes built off original plans , in Au, the floors and fitting cast in this, something like 33% of the thickness of mild steel were the chainplates. unfortunately the ship would need to be riveted to transverse frames An old skill
    good question though
     
  4. Ad Hoc
    Joined: Oct 2008
    Posts: 7,774
    Likes: 1,679, Points: 113, Legacy Rep: 2488
    Location: Japan

    Ad Hoc Naval Architect

    Alan, in a forum, you can discuss whatever you like :)

    The best way, to keep costs down, would be to make the hull only from copper-nickel. The internal frames and decks can be made from cheaper mild steel. You can weld it with simple 70/30 copper-nickel or Monel welding rods.

    Would be an interesting exercise, to see what the overall cost would be.

    But you would have to be very careful that all underwater items to be made the same or from a more noble metal.
     
  5. brian eiland
    Joined: Jun 2002
    Posts: 5,067
    Likes: 216, Points: 73, Legacy Rep: 1903
    Location: St Augustine Fl, Thailand

    brian eiland Senior Member

  6. brian eiland
    Joined: Jun 2002
    Posts: 5,067
    Likes: 216, Points: 73, Legacy Rep: 1903
    Location: St Augustine Fl, Thailand

    brian eiland Senior Member

    Looks like the old reference websites I sited in that discussion are no longer where they were formerly located. So if you wish to see that material, I imagine you will have to contact the assoc directly for an update as to where you might find the articles
     
  7. alanrockwood
    Joined: Jun 2009
    Posts: 133
    Likes: 17, Points: 18, Legacy Rep: 116
    Location: USA

    alanrockwood Senior Member

  8. brian eiland
    Joined: Jun 2002
    Posts: 5,067
    Likes: 216, Points: 73, Legacy Rep: 1903
    Location: St Augustine Fl, Thailand

    brian eiland Senior Member

  9. welder/fitter
    Joined: Jun 2008
    Posts: 407
    Likes: 32, Points: 0, Legacy Rep: 423
    Location: Vancouver

    welder/fitter Senior Member

    Alan,
    As has been mentioned, Cu-Ni has been used & many alloyed steels with varied amounts of chromium & nickel are worthy of consideration, keeping weldability, etc., in mind. While Cor-ten has taken a beating in many threads, here & elsewhere, it is but one example of a family of HSLA (high strength, low alloy) steels, as well. For a one-off design, however, it is challenging to weigh the construction costs & issues against the perceived benefits.

    Don't ever hesitate to ask questions, suggest things, etc., on this site. I have learned a lot from others, here, by doing so.

    Mike
     
  10. Dean Smith

    Dean Smith Previous Member

    there was an AC yacht, think was Ranger? in 1930s, she was bronze under water and alu above, needless to say the alu lasted til lunchtime
    Copper sheet is wonderful on boats esp oak, which the worms are into like fruitcake, sheeved in Cu the hull just lasts and lasts
     
  11. nemier
    Joined: Jan 2004
    Posts: 26
    Likes: 5, Points: 3, Legacy Rep: 15
    Location: Panama

    nemier Junior Member

    Google 'Michael Kasten'
    He discusses this material for hulls, in some depth. Quite interesting.
     
    1 person likes this.
  12. Adler
    Joined: Jan 2010
    Posts: 183
    Likes: 17, Points: 18, Legacy Rep: 139
    Location: PIRAEUS - GREECE

    Adler Senior Member

  13. mitiempo
    Joined: Feb 2009
    Posts: 18
    Likes: 1, Points: 0, Legacy Rep: 14
    Location: Victoria B.C. Canada

    mitiempo Junior Member

    Why not titanium? Interesting article in Professional Boatbuilder (#132 - August/September 2011) about titanium and its properties and a short profile of a 42' sailboat built in Japan entirely of the material. It's on page 62.
     
  14. Tanton
    Joined: Nov 2003
    Posts: 992
    Likes: 93, Points: 38, Legacy Rep: 294
    Location: Newport RI

    Tanton Senior Member

    C-n

    TYD#964. 63'
    C-N Bottom.
     

    Attached Files:

    1 person likes this.

  15. Ilan Voyager
    Joined: May 2004
    Posts: 1,292
    Likes: 225, Points: 63, Legacy Rep: 758
    Location: Cancun Mexico

    Ilan Voyager Senior Member

    No it was Reliance, designed and built by Nathanael Herreshoff in 1905. The NA knew perfectly that wouldn't last but it was not a problem for an America's cup sailboat.
    Made in Aluminum for above water, Tobin bronze under water over structure in steel...great galvanic mix.
    On wood boats copper sheet is the best solution in tropical waters (very old technique initiated by the English for war ships in the 17 th century)
     
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.