New member restoring 15' powercat, transom and hull overhaul

Discussion in 'Fiberglass and Composite Boat Building' started by elwesso, Jan 27, 2011.

  1. elwesso
    Joined: Nov 2006
    Posts: 7
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Indiana

    elwesso Junior Member

    Hey guys, great forum here.. I have spent a bit of time reading through previous posts on here, as well as other places on the internet. Looks like great information!

    I apologize if this is the wrong forum to post in....

    Anyway, my winter pet project is restoring this '64 powercat, its been sitting outside for about 30 years since it was last used.. I am intending on doing a full restoration on it to get it back to its glory days.. Without going into a lot of history on the boat, here is what I am intending on doing.

    Ive done a bit of research on the powercats, and it appears the only strutctural things I have to worry about are replacing the rotten plywood in the transom and the hulls, so that is the first thing for me to look at..

    I already have the deck and the hull mostly separated, so I am ready to start digging out the old transom and hull materials..

    The research I've done shows that some of the "pourable type" transom materials seem to be better than plywood, and overall a simpler solution.. The products Ive heard of are the Seacast product, as well as the NidaCore product...

    The fact is this boat was originally built as a racer, so the idea of something thats lighter, stronger, and inpervious to moisture is very appealing, not to mention it seems to be much simpler than forming a piece of plywood and glassing it back in..

    It appears to me that the hull of the boat is in pretty good shape, the glass seems to be in good shape, and theres no abrasions or major hull damage, so it *appears* that once the transom and hulls are replaced, that should be about all it needs other than some fresh paint..

    My plan right now is to use one of these pourable transoms.. I will remove the inner skin, which is really just the sprayed on fiberglass (the term escapes me), so I'll dig the old transom out from the inside and put in place something on the inside to cast the new transom..

    The same idea goes for the floor.. Seacast also makes a self leveling floor compound which would be great, because I would dig up the old plywood in the hulls and just let it sit, and that would be done..


    Thanks in advance for any advice!!!
     
  2. Lurvio
    Joined: Jul 2009
    Posts: 283
    Likes: 18, Points: 0, Legacy Rep: 249
    Location: Mid of Finland

    Lurvio Mad scientist

    Could you scale down the pictures to something like 800x600 pixels. It's a pain to try and read a post like this. Any image editing software can to this, MS Paint, Gimp etc.

    Lurvio
     
  3. elwesso
    Joined: Nov 2006
    Posts: 7
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Indiana

    elwesso Junior Member

  4. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    Sir those boats had great racing background,I would never use a pour-able in it when there are many other options,Like high density foams such as coosa board and some west system epoxy which is sold everywhere. There were 4 variants of the powercat I think.

    standard non stepped twin hull catamaran

    standard non stepped trimaran

    Three Point hydro

    four point Hydro cat.
     
  5. elwesso
    Joined: Nov 2006
    Posts: 7
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Indiana

    elwesso Junior Member

    Thank you for your reply!! So basically you are suggesting that is superior to use another core material like high density foam or coosa board....

    I would appreciate any other insights.
     

  6. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    Exactly, that is a old boat and would use Epoxy on the rebuilding job,I mentioned West Systems, they have a website where you can get info.
     
Loading...
Similar Threads
  1. Outwith Jack
    Replies:
    2
    Views:
    734
  2. Eddie A
    Replies:
    7
    Views:
    2,217
  3. Franklin
    Replies:
    5
    Views:
    883
  4. UtahSignature
    Replies:
    29
    Views:
    2,402
  5. E350
    Replies:
    28
    Views:
    3,695
  6. grendel54
    Replies:
    34
    Views:
    5,288
  7. skier51423
    Replies:
    14
    Views:
    2,539
  8. jetboater455
    Replies:
    0
    Views:
    1,910
  9. Josh87
    Replies:
    6
    Views:
    5,440
  10. e32lover
    Replies:
    23
    Views:
    17,013
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.