Bead and Cove Router Bits - Where to buy in USA?

Discussion in 'Boatbuilding' started by CatBuilder, Dec 18, 2010.

  1. CatBuilder

    CatBuilder Previous Member

    I've been looking around for bead and cove router bits and have come up with nothing.

    I have 1" thick foam to bead and cove.

    Any suggested vendors?
     
  2. alan white
    Joined: Mar 2007
    Posts: 3,730
    Likes: 123, Points: 0, Legacy Rep: 1404
    Location: maine

    alan white Senior Member

    I looked for bits that would join 1" thick materials and I found that there's not much out there. Most every company appears to be completely ignorant of the fact that measurements need to be supplied. They say nothing of radius (which is the vital statistic) because the company is made up of people who know nothing of their product except its catalog number. Welcome to 2010.
    I will suggest this: the cove part can be made by running the foam through a table saw on edge, at an angle (as viewed from above--- using a fence somewhat at an angle to the regular rip fence). Any size cove can be done this way.
    The bead can be done using a standard round-off bit with a 1/2" radius---- the first edge with the router flat on the panel. The second half with the router on the edge of the panel (otherwise the bearing will ride too deep). Do you understand?
     
  3. wardd
    Joined: Apr 2009
    Posts: 897
    Likes: 37, Points: 0, Legacy Rep: 442
    Location: usa

    wardd Senior Member

  4. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    Norton Carbide Tools
    5775 Orange Drive
    Davie, FL 33314-3819
    (954) 587-8665


    That is where I get my custom carbide tooling and these as well.




    [​IMG]


    [​IMG]
     
  5. CatBuilder

    CatBuilder Previous Member

    Thanks, Alan and Wardd. I do understand the method, but my coves have to be exact and I easily have 4500ft+ of coving (and beading) to do. Damn close to a mile! :)

    I need to do what War Whoop is showing in the picture. Thanks for the referral to Norton Carbide, Mr. Whoop. I'll give them a try.
     
  6. alan white
    Joined: Mar 2007
    Posts: 3,730
    Likes: 123, Points: 0, Legacy Rep: 1404
    Location: maine

    alan white Senior Member

    Great info, Wardd. I know the trick of tilting the saw blade, which I've use to "generate" complex moldings (to match century-old moldings in old houses). I still think the table saw process is as good or better than the router bit method, maybe because I own the table saw and I don't have a mini-shaper. I'm glad someone supplied the vendor for you, any case.
     
  7. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    Two large routers on a 1" MDF topped Bench, the One shown was the bead, the core box bit was on the other side,it captured the planks and held a exact cove.
     
  8. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    You don't need a 1" bit for 1" foam. A 3/4" will leave only 1/8" square edges which will not be a problem.
     
  9. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    Go full size

    [​IMG]
     
  10. SamSam
    Joined: Feb 2005
    Posts: 3,899
    Likes: 200, Points: 63, Legacy Rep: 971
    Location: Coastal Georgia

    SamSam Senior Member

    Coves made with a table saw blade are not of a set radius, they are elliptical in shape and so can't be matched with any bead router bit.
     
  11. TeddyDiver
    Joined: Dec 2007
    Posts: 2,614
    Likes: 136, Points: 73, Legacy Rep: 1650
    Location: Finland/Norway

    TeddyDiver Gollywobbler

    Correct, but the difference is insignificant as long as the depth of the cove is reasonable..
     
  12. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    Coves made with a table saw are not eliptical but circular. They are not a half circle however, which most half round bits are. There will be more glue needed to fill the gap.
     
  13. SamSam
    Joined: Feb 2005
    Posts: 3,899
    Likes: 200, Points: 63, Legacy Rep: 971
    Location: Coastal Georgia

    SamSam Senior Member

  14. War Whoop
    Joined: Jun 2003
    Posts: 661
    Likes: 16, Points: 0, Legacy Rep: 84
    Location: Sunny Ft Lauderdale Fla

    War Whoop Senior Member

    The beauty of the system is it's ability to wrap a curved surface with smaller planks and a full size joint is required for this so the planks bead is not raised in the cove through slight rotation off a shoulder creating a unnecessary Putty filled expensive and heavy joint when the core is desired.

    The feather edges are fine long as care is used.
     

  15. PAR
    Joined: Nov 2003
    Posts: 19,126
    Likes: 498, Points: 93, Legacy Rep: 3967
    Location: Eustis, FL

    PAR Yacht Designer/Builder

    Considering the linear amount of cove and bead work you need, Catbuilder, a custom bit set is a reasonable option. Personally, I make them up my self, but many don't work metal, know how to weld, have the tools, etc., so a local machine shop can fix you up for not much money.
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.