Accruate Developable Panels

Discussion in 'Software' started by Grant Nelson, Apr 6, 2010.

  1. lewisboats
    Joined: Oct 2002
    Posts: 2,329
    Likes: 129, Points: 0, Legacy Rep: 1603
    Location: Iowa

    lewisboats Obsessed Member

    Developability check in F/Dship will tell you where the problems lie...but it depends on the material in question. It was designed for steel so if you are using plywood you can often obtain results that are...in F/Dship...not achievable. Best to look at the total error and edge error in the develop plates section and judge from there. Anything under .005 is probably gettable out of ply of a reasonable thickness with a bit of torture.
     
  2. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    I've been pretty pleased with the Devsrf plugin for Rhino. It produces a nice set of ruling lines to give some idea of how a panel will unroll. I have not yet tested the real-world accuracy of panels created with devsrf and unrollsrf.

    Fair lines and realistic curvature are critical. Ideally, the porcupine plots of the surface edges and isocurves should be continuous and smooth; I'll settle for continuous if need be, but discontinuities or zero crossings in the porcupines do not bode well for developable panel accuracy (or hull fairness in general). Keeping point count to a minimum, keeping uniform point weights and avoiding tweaks to the knot vectors (keep them uniform, no duplicate values in the middle) will make it much easier to keep things fair.
     
  3. thommie84
    Joined: Jun 2010
    Posts: 8
    Likes: 1, Points: 3, Legacy Rep: 35
    Location: Rotterdam

    thommie84 Junior Member

    Does "smash" also show the strain as it does in Workshop (Maxsurf)?
     
  4. marshmat
    Joined: Apr 2005
    Posts: 4,127
    Likes: 149, Points: 63, Legacy Rep: 2043
    Location: Ontario

    marshmat Senior Member

    Smash will tell you the change in area, but it doesn't show the strains. I've also found that for panels that are close to developable, Smash can be inaccurate. I've taken to using Unrollsrf on a true developable panel that shares the two longest edges of the nearly-developable one, then using the shape produced by Smash from the true panel to correct the shorter edges. Roundabout, yes, but it seems to work for things that are just a little bit off developable in a few spots.
     
  5. sissi
    Joined: Jun 2010
    Posts: 3
    Likes: 0, Points: 0, Legacy Rep: -10
    Location: florida

    sissi New Member

  6. apex1

    apex1 Guest

    Do you earn your living by spreading this ad around? :(
    Where is that product related to this thread?
     
  7. thommie84
    Joined: Jun 2010
    Posts: 8
    Likes: 1, Points: 3, Legacy Rep: 35
    Location: Rotterdam

    thommie84 Junior Member

    indeed this has nothing to do with predicting development of plates with various software sollutions...
     
  8. The Loftsman
    Joined: Jun 2010
    Posts: 91
    Likes: 4, Points: 0, Legacy Rep: 41
    Location: The Loft

    The Loftsman The Loftsman

    These post,s and so many more all seem to be adverts for this or that software etc,etc. I can develope shell with compound curvature, or with double curvature etc,etc and all because i served a long apprentice ship to learn how to Loft Ship's/Boats, there are no short cuts and it seems to me that most people think you just push a couple of buttons on a keyboard and hey presto all your design challenges are over.

    The Loftsman
     
  9. David Cockey
    Joined: Sep 2009
    Posts: 9
    Likes: 1, Points: 0, Legacy Rep: 36
    Location: Michigan

    David Cockey Junior Member

    McNeel now recommends using Squish instead of Smash for flattening non-developable surfaces. Squish has a number of options for how to stretch or compress the surface during the flattening, and can provide a graphical representation of where the maximum distortion occured.

    http://wiki.mcneel.com/labs/advancedflattening

    Squish needs to be downloaded; its not included in the standard Rhino 4.
     
  10. DCockey
    Joined: Oct 2009
    Posts: 5,229
    Likes: 634, Points: 113, Legacy Rep: 1485
    Location: Midcoast Maine

    DCockey Senior Member

    What assumptions about stretch and compression do you use when developing a shell with compound/double curvature?
     

  11. The Loftsman
    Joined: Jun 2010
    Posts: 91
    Likes: 4, Points: 0, Legacy Rep: 41
    Location: The Loft

    The Loftsman The Loftsman

    Compound Curves?

    This i consider to be an art, and not as yet for general consumption of freinds i dont really know yet?
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.