Weed eater engine conversion

Discussion in 'DIY Marinizing' started by Ward, Jun 2, 2003.

  1. jdc1111
    Joined: Feb 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: TX

    jdc1111 New Member

    Updated plans

    Mark, I really like that handle, it's a great solution. Tons of great ideas on this forum. I think I'm stuck until I get a motor in hand. Here's some updated plans what I'm looking to build.
    I think I'm going to use galvanized electrical conduit, since it's super cheap, light, and pretty weather resistant (should outlast my engine). The 1/2" conduit is $2 for 10ft, and has a 5/8" inner diameter at Lowes. 1/2" black iron pipe is also 5/8" ID (brought my caliper), but a little more pricey. It's more rigid. I got some bushings 3/8" ID and 5/8" OD, think I can make it work.
     

    Attached Files:

  2. muddin redneck
    Joined: Jun 2009
    Posts: 95
    Likes: 3, Points: 0, Legacy Rep: 34
    Location: Muscatine, Iowa

    muddin redneck DO IT IN THE MUD!!!

    jdc mud motor draft #2

    jdc,
    your design looks good, only one question. does your engine turn counter clockwise if so you have your idler sprocket on the wrong side. REASON: you dont want the idler sprocket on the side of the chain that does the pulling which would be the right side looking at the drive shaft. with the CCR the left side will be going down and it will have the slack on that side of the chain so that is the side you want you idler on. clear as mud right!!! any question you still have on the idler just pm me. (2.Tension adjusted via bolt/nut running through slot in frame, idler pulley freewheels on bolt shaft, nut locks the pulley bolt onto the slot when in position) does the idler you will use have a bearing in it. the idler sprocket needs one in it not just spinning on a bolt it will wear out. if not use something like this. http://www.mcmaster.com/#6663k11/=5w54tx one more thing not sure if the conduit will be strong enough to withstand the torque of the prop running through mud and weeds, i would use 1" x 1/8" DOM tubing with 3/4" od x 3/8" or 1/2" id bushings. not trying to be an *** just trying to give as much info as possible to help you make your decision
     
  3. wac m trac m
    Joined: Jun 2008
    Posts: 75
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Texas

    wac m trac m Junior Member

    I agree..you need to cover that chain..it's very dangerous being the number 1 reason and 2 it would be a pain having to clean the sprocket all the time.

    A box with sealed bearings with solve that problem.
    You can order you some thicker walled conduit in any size you need online..there a bunch of places to order from..find one near you. I would try to keep everything light cause it will get heavy real fast with all the goods.
     
  4. csimms
    Joined: Feb 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Idaho

    csimms New Member

    Thai/ Longtails


    John,

    Have you completed the 3hp Honda with the shorter shaft yet? Would be curious to see pics.

    I have been emailing Paraprop figuring out options to build my new motor. I would like to build one using the 2.5hp engine from harbor freight and have a shorter shaft than what paraprop is using with his longtail kits.

    I'm not even sure that 2.5hp engine will work with his aluminum coupler.

    Any thoughts???
     
  5. pistnbroke
    Joined: Jan 2009
    Posts: 1,405
    Likes: 34, Points: 48, Legacy Rep: 404
    Location: Noosa.Australia where god kissed the earth.

    pistnbroke I try

    just a thought $599 6.5 hp lifan....looks like a left hand prop to me
     

    Attached Files:

  6. Wolfgang123
    Joined: Apr 2009
    Posts: 42
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Atlanta

    Wolfgang123 Junior Member

    where did you find that looks like the commerical 6:1 gear reduction 6.5hp
     
  7. pistnbroke
    Joined: Jan 2009
    Posts: 1,405
    Likes: 34, Points: 48, Legacy Rep: 404
    Location: Noosa.Australia where god kissed the earth.

    pistnbroke I try

    on www.ebay.com.au i think 6:1 would be too much judging by the prop ..they usually go about 1: 1.6 to judge by the genuine Briggs and Stratton outboard
     
  8. Wolfgang123
    Joined: Apr 2009
    Posts: 42
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Atlanta

    Wolfgang123 Junior Member

    can you post a link?
     
  9. pistnbroke
    Joined: Jan 2009
    Posts: 1,405
    Likes: 34, Points: 48, Legacy Rep: 404
    Location: Noosa.Australia where god kissed the earth.

    pistnbroke I try

    There is no more information in the e bay listing ..the guy does not even say its a 6.5 lifan ..the pictures tell it all No prop pitch gear ratios at all just 205 cc
     
  10. John O`Neal
    Joined: Sep 2007
    Posts: 85
    Likes: 1, Points: 0, Legacy Rep: 29
    Location: Lenexa Ks.

    John O`Neal Junior Member

    The 2.5 hp engine will easily adapt to the aluminum coupler as shown below. The coupler is made to accept a 3/4" output shaft . The 2.5 hp engines sold at Harbor Freight are listed as having 5/8" output shafts . The remedy is a split reducer bushing and a stepped key-way. I purchased mine at Grainger for around $3.00 . It works fine. I used the 5 1/2' prop they offer with the smaller engine and it seemed to work the best. Haven`t been able to finish the Honda GX100 project yet, but hope to get to it soon.
    [​IMG]
    [​IMG]
    [​IMG]
     
  11. JOBBER
    Joined: Sep 2008
    Posts: 8
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: carol stream, il 60188

    JOBBER Junior Member

    PISTNBROKE motor

    Looks like a nice "vertical" unit. I have been looking for any kind of small unit which is air cooled. I live in Illinois, USA. Using a water cooled motor before lakes are ice bound, has motor freezing issues. Do you have anymore info on it? Do you know if a long shaft version is available? B&S only makes a short shaft. Thanks
     
  12. Mark Wo
    Joined: Dec 2007
    Posts: 143
    Likes: 5, Points: 0, Legacy Rep: 56
    Location: Minnesota

    Mark Wo Senior Member

  13. csimms
    Joined: Feb 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Idaho

    csimms New Member

    Thai/ Longtails

    Thanks for the information. Do you have any idea what the total weight is of the 2.8hp set up?

    Chris
     
  14. John O`Neal
    Joined: Sep 2007
    Posts: 85
    Likes: 1, Points: 0, Legacy Rep: 29
    Location: Lenexa Ks.

    John O`Neal Junior Member

    It weighs in at 63lbs .
     

  15. csimms
    Joined: Feb 2010
    Posts: 4
    Likes: 0, Points: 0, Legacy Rep: 10
    Location: Idaho

    csimms New Member

    That is probably to heavy for my boat.

    I was originally looking at the Duropower brushcutter conversion for my motor. Sounded fairly easy. After doing some research recently I found that Duropower no longer sells the brushcutters or the individual small engines for the brushcutters. The only companies that are making the brushcutters with the larger displacement motors are selling them anywhere from $800 to $1000.

    If you still have your original Duropower motor, I would be willing to buy it!!!
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.