Cat Centerboards Single vs Twin.

Discussion in 'Multihulls' started by Zed, Feb 5, 2010.

  1. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    Could a single central board match the traditional setup of one in each hull?
     
  2. Doug Lord
    Joined: May 2009
    Posts: 16,679
    Likes: 349, Points: 93, Legacy Rep: 1362
    Location: Cocoa, Florida

    Doug Lord Flight Ready

    ================
    Yes ,if the surface piercing nature of the foil was understood and dealt with.
    The bi-plane rigged cat "Happy Feet" uses such an arrangement. They seem to have good speed but break things too often.
    ---------
    I just remembered the 27' Stilleto had a single board and was/is a fairly high performance cat: "Stiletto has an unusual single centerboard that varies her draft from a maximum of four feet to a minimum of nine inches; with her kickup rudders, she is easily beachable. "
    http://www.thebeachcats.com/Article124.html
     

    Attached Files:

  3. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    Meaning?

    Simple Engrish PLS! :D
     
  4. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    Cool, thanks.

    Any benefit in tacking?
     
  5. Doug Lord
    Joined: May 2009
    Posts: 16,679
    Likes: 349, Points: 93, Legacy Rep: 1362
    Location: Cocoa, Florida

    Doug Lord Flight Ready

    ===================================
    1) angling the board slightly forward( about 7 degrees) of vertical to reduce the chance of ventilation
    2) and,if necessary, adding a fence to the board a few inches below the point the waters surface contacts the board when the windward hull is just slightly out of the water.

    multiple fences:
     

    Attached Files:

  6. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    This is because of the lack of a hull/end plate so to speak... no?
     
  7. Doug Lord
    Joined: May 2009
    Posts: 16,679
    Likes: 349, Points: 93, Legacy Rep: 1362
    Location: Cocoa, Florida

    Doug Lord Flight Ready

    ------------------------
    Thats a good question. A cat with twin boards can use twin asymetric boards or "toe-in" the daggerboard trunks so the boards eliminate the hull drag associated with leeway. A single board would either have to use a trailing edge flap or rotate a few degrees to windward tack to tack(gybing board) to match the effectiveness of the asymetrical/toed-in boards. Even with this the single board has an edge in weight and ease of handling.
    However, if you want to generate vertical lift there is a whole 'nother set of considerations.....
    Tacking is not affected one way or the other that I have been able to tell.
     
  8. Doug Lord
    Joined: May 2009
    Posts: 16,679
    Likes: 349, Points: 93, Legacy Rep: 1362
    Location: Cocoa, Florida

    Doug Lord Flight Ready

    ------------------
    Yes, sure. The hydrofoil Moth has a similar problem when sailed upwind level and to a lesser extent when sailed with veal heel. They've used the angled forward daggerboard "trick" successfuly w/o fences.
     
  9. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    Happy Feet

     
  10. Doug Lord
    Joined: May 2009
    Posts: 16,679
    Likes: 349, Points: 93, Legacy Rep: 1362
    Location: Cocoa, Florida

    Doug Lord Flight Ready

    Cool-thanks!
     
  11. sabahcat
    Joined: Dec 2008
    Posts: 792
    Likes: 28, Points: 0, Legacy Rep: 273
    Location: australia

    sabahcat Senior Member

    comment at 55 seconds

    "so busy trying to make money at the moment its great"

    Always someone to fleece in Thailand eh
     
  12. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    Yeah noticed that comment!

    I like the boom gooseneck/vang configuration.

    How to they manage mainsail twist? Or don't they?
     
  13. ThomD
    Joined: Mar 2009
    Posts: 561
    Likes: 25, Points: 18, Legacy Rep: 111
    Location: TO

    ThomD Senior Member

    Didn't simpson do a cat like that, and Chris White has one, ad K-designs.... .

    A lot of them have been done, and yet it really never seems to become standard. So for instance consider the Tikis, somewhere in there Wharram gets the religion on foils and starts adding these relatively hidious fixed keels. If there were some standard well understood details for a mid mounted one that could be pulled in when the next Perfect Storm comes along it would seem a natural. Not making a point, just wonder about it from time to time.

    Also, it depends what you mean by "match". A similar boat with central spar and lateral boards woould structurally be possible in wood, while I suspect Happy feet had to step it up to carbon fiber.
     
  14. rayaldridge
    Joined: Jun 2006
    Posts: 581
    Likes: 26, Points: 0, Legacy Rep: 322
    Location: USA

    rayaldridge Senior Member

    I think a better approach than a central board is one daggerboard in one hull. There's really no necessity to have twin boards. All of John Shuttleworths cruising designs use a single board, I believe, and he says he conducted thorough tank tests.

    The Stiletto was fast with a single central board, but faster with boards endstopped by the hull.
     

  15. Zed
    Joined: May 2009
    Posts: 232
    Likes: 13, Points: 0, Legacy Rep: 179
    Location: Australia

    Zed Senior Member

    I want to avoid cases exiting into the water on a moored boat.

    Thom,

    I would like to retain windward performance as much as is possible. Yes it never has caught on so I ask why? What don't I know? Am I missing something big?
     
Loading...
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.