Infusion: Is pulling resin down the laminate a bad idea?

Discussion in 'Fiberglass and Composite Boat Building' started by ahender, Feb 19, 2009.

  1. ahender
    Joined: Jan 2009
    Posts: 91
    Likes: 4, Points: 8, Legacy Rep: 10
    Location: Athens, GA USA

    ahender Junior Member

    Hi:

    I have a resin infusion question.

    I am in the process of infusing a male canoe mold.

    I understand that the resin bucket needs to be lower than the part.

    Am I wrong in assuming that I can place the resin infusion line at the top of my male mold with the resin flowing downward?

    thanks...alan
     
  2. KnottyBuoyz
    Joined: Jul 2006
    Posts: 829
    Likes: 56, Points: 0, Legacy Rep: 685
    Location: Iroquois, Ontario

    KnottyBuoyz Provocateur & Raconteur

    Possible. Unusual I believe. You'll need multiple vacuum lines that you can individually shut off when the resin reaches them or you'll likely end up filling up your catch pot with resin. Conventional setup would be to feed the resin in around the bottom with a single (2 or 3 is ok too) vacuum exit on the top edge. When the part is about 3/4 infused you'd shut off the resin feed and let the vacuum continue to distribute the resin through your whole layup. This way you'll waste no resin and end up with a better (resin/fibre) ratio in your layup.
     
  3. ahender
    Joined: Jan 2009
    Posts: 91
    Likes: 4, Points: 8, Legacy Rep: 10
    Location: Athens, GA USA

    ahender Junior Member

    Thanks Rick.

    I have never read about shutting off the resin line at the 3/4 point.

    I think I have read every article ever posted on the Internet, but have never seen that.

    Are there any caveats as to when that can't be done -- like a less than desirable vacuum (say ~20") or other variables.

    I learned the hard way yesterday on using a HVAC vacuum pump, as opposed to a heavier duty "continuous use" model.

    In my case both my primary and secondary pumps failed after 2 hours of continuous use due to heat.

    I pretty much had to stay with the project all afternoon until thin set so that I could manually roll everything out.

    Now I have experience!

    Thanks..alan
     
  4. Landlubber
    Joined: Jun 2007
    Posts: 2,640
    Likes: 125, Points: 0, Legacy Rep: 1802
    Location: Brisbane

    Landlubber Senior Member

    Yeah it is standard practice to shut off the resin before full saturation, however there is nothing wrong with the resin above the job ( as long as you have it valved of course).
     
  5. gamecock413
    Joined: Jan 2009
    Posts: 15
    Likes: 1, Points: 0, Legacy Rep: 20
    Location: SC

    gamecock413 Junior Member

    I think i got the image in, you can do this, it works well.
     

    Attached Files:

    1 person likes this.
  6. gamecock413
    Joined: Jan 2009
    Posts: 15
    Likes: 1, Points: 0, Legacy Rep: 20
    Location: SC

    gamecock413 Junior Member

    oh yeah, if you are going to use epoxy you are going to need to ramp up the temp of your part after infusion to gel the resin. otherwise you will get outgassing and undesirable bubbles.the supply pot was good at just below the flange of the mold. a polyethelene rope was used for even vacuum around the mold, incatec is the 3 black strips with three infusion ports, but only one supply pot and one vacuum. I am assuming you know everything else you need.

    This is a finished version of that boat. This one was handlayed though. the infused is still in trim out. It sold at the NE Boat show this past weekend.
     

    Attached Files:


  7. JRL
    Joined: May 2007
    Posts: 83
    Likes: 2, Points: 0, Legacy Rep: 25
    Location: Palm Beach Gardens, FL

    JRL Im with stupid

    You can do that. You have to surround the entire part with vacuum. I made some radom couplers using that exact method. Just make sure ever square inch of cloth you want to wet out is covered in some type of flow medium.
     
Loading...
Similar Threads
  1. EngineeringEC
    Replies:
    13
    Views:
    1,006
  2. Florida Boat Guy
    Replies:
    15
    Views:
    2,092
  3. ber1023
    Replies:
    2
    Views:
    1,118
  4. fallguy
    Replies:
    11
    Views:
    1,261
  5. John Slattery
    Replies:
    14
    Views:
    1,618
  6. Steve W
    Replies:
    33
    Views:
    2,214
  7. weldandglass
    Replies:
    1
    Views:
    870
  8. Chotu
    Replies:
    8
    Views:
    1,208
  9. weldandglass
    Replies:
    2
    Views:
    1,148
  10. weldandglass
    Replies:
    6
    Views:
    1,609
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.