Search Results

Search Again
Page 1 of 4
  1. nautical
    Post

    Location of VCG/KG

    Thank you Dingo for sharing.
    Post by: nautical, May 26, 2007 in forum: Stability
  2. nautical
    Post

    cold moulding vs fiber glass

    Frosh when I have a question on windsurfing I will ask you for your opinion. So stick to the topic.
    Post by: nautical, May 11, 2007 in forum: Wooden Boat Building and Restoration
  3. nautical
    Post

    cold moulding vs fiber glass

    Thanks Raggi Thor.
    Post by: nautical, May 11, 2007 in forum: Wooden Boat Building and Restoration
  4. nautical
    Post

    cold moulding vs fiber glass

    Raggi Thor I am very aware of those things. I am not building anything yet or maybe not anytime soon. I am learning :)
    Post by: nautical, May 10, 2007 in forum: Wooden Boat Building and Restoration
  5. nautical
    Post

    cold moulding vs fiber glass

    frosh. you are wrong I am not asking anyone for the best construction method. I asked for some pro and cons. and asked for some sources. And...
    Post by: nautical, May 10, 2007 in forum: Wooden Boat Building and Restoration
  6. nautical
    Post

    cold moulding vs fiber glass

    Thanks par. you have been very helpful. I have collected a few books and got the dave gerrs book too. very nicely explained.
    Post by: nautical, May 10, 2007 in forum: Wooden Boat Building and Restoration
  7. nautical
    Post

    engine question

    because total power is 900 HP extra a little of extra power to operate at low RPM for fuel consumption (Ranchi) gear ratio 3. Maximum Engine...
    Post by: nautical, May 9, 2007 in forum: Diesel Engines
  8. nautical
    Post

    engine question

    where are the values . its 2 volvo penta D12-615 ZF 350 1 IV gearbox
    Post by: nautical, May 9, 2007 in forum: Diesel Engines
  9. nautical
    Post

    engine question

    Kjell thanks very much for the program again I tried to varify my values with r program. can you check it with ur program .. I have posted all the...
    Post by: nautical, May 9, 2007 in forum: Diesel Engines
  10. nautical
    Post

    engine question

    Fast Fred says to run the numbers on 80 percent ratings. Gerr says to run the numbers on Maximum ratings. ???? Ranchi thanks for ur...
    Post by: nautical, May 9, 2007 in forum: Diesel Engines
  11. nautical
    Thread

    Z drives

    Lets Talk about Z drives here. Are they used for primary source of propulsion or they are used as thurusters for good maneuverabilty
    Thread by: nautical, May 8, 2007, 0 replies, in forum: Diesel Engines
  12. nautical
    Post

    Pictures of my current project

    Very nice work.
    Post by: nautical, May 8, 2007 in forum: Wooden Boat Building and Restoration
  13. nautical
    Post

    cold moulding vs fiber glass

    Thanks again PAR i will sure find that book very soon. I checked our library and I didnt find the book or found some books on plywood boat...
    Post by: nautical, May 8, 2007 in forum: Wooden Boat Building and Restoration
  14. nautical
    Post

    engine question

    The '' Folks" I meant are the academic folks remeber this is academic. Anyway I have changed a little bit. took 615 hp engine with a lower...
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
  15. nautical
    Post

    engine question

    do u have the bp delta chart for EAR 0.65
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
  16. nautical
    Post

    engine question

    well i totally agree with you. ranchi, but the folks who will be looking at this will be asking why i have taken a larger engine when the power...
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
  17. nautical
    Post

    engine question

    well i totally agree with you. ranchi, but the folks who will be looking at this will be asking why i have taken a larger engine when the power...
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
  18. nautical
    Post

    engine question

    well I have changed the speed Lets say here are the details LWL 30 m BWL 7.6 m Draft 1.55 m Displacement = 124 tons Service speed 13.3...
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
  19. nautical
    Post

    engine question

    The diameter is 40 Inches. I cant get anything better than that. IF the redutions ratios were highr maybe i could get a lower propeller RPM and...
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
  20. nautical
    Post

    engine question

    Thanks Ranchi. Seems to have solved the problem Maximum Engine RPM 2600 Propeller RPM 1020 Screw B 4.55 Efficiency 56 % (behind hull...
    Post by: nautical, May 8, 2007 in forum: Diesel Engines
Showing results 1 to 20 of 72 Next >
Search Again
Page 1 of 4