Search Results

Search Again
Page 1 of 2
  1. reelpleasure
    Thread

    Working with NidaCore (Plascore) panels and Nida Core Bonding compound

    I did some experimenting yesterday with a couple of pieces of scrap Plascore. The pieces are leftover cuts from stringers going into the 25 T...
    Thread by: reelpleasure, May 27, 2014, 0 replies, in forum: Fiberglass and Composite Boat Building
  2. reelpleasure
    Post

    Polyester resin over polyurethane enamel

    one part
    Post by: reelpleasure, May 15, 2014 in forum: Materials
  3. reelpleasure
    Thread

    Polyester resin over polyurethane enamel

    Question for the paint and resin experts??? I am rehabbing my 25 Terry Jason lobster boat. The helm dash is reconfigured and I have a...
    Thread by: reelpleasure, May 15, 2014, 4 replies, in forum: Materials
  4. reelpleasure
    Post

    Layup schedule for Nidacore deck joists??

    6 joists all laminated up. Dark ones are VE resin with red MEK Light ones are polyester with clear MEK
    Post by: reelpleasure, May 6, 2014 in forum: Fiberglass and Composite Boat Building
  5. reelpleasure
    Post

    Vinylester layup over H80 core 2 sides at once

    The VE resin was purchased from Hamilton Marine in Portland Maine. I had NO issues with fast gel time/heat etc. with 20cc of MEK to 32 oz of...
    Post by: reelpleasure, May 6, 2014 in forum: Fiberglass and Composite Boat Building
  6. reelpleasure
    Post

    Vinylester layup over H80 core 2 sides at once

    I've been using 20cc per 32 oz of vinyl ester resin with good results laying up nidacore joists.
    Post by: reelpleasure, May 5, 2014 in forum: Fiberglass and Composite Boat Building
  7. reelpleasure
    Thread

    Layup schedule for Nidacore deck joists??

    I rebuilding a 25 foot lobster boat for recreational use. Over the fall and winter I removed the back deck and removed everything except from the...
    Thread by: reelpleasure, May 4, 2014, 3 replies, in forum: Fiberglass and Composite Boat Building
  8. reelpleasure
    Thread

    Nidacore layup schedule

    As I go forward with my rebuild/rehab/repower of my 1989 25 T Jason lobster boat, I'm getting to the point of laying up and glassing in lateral...
    Thread by: reelpleasure, Mar 4, 2014, 1 replies, in forum: Fiberglass and Composite Boat Building
  9. reelpleasure
    Post

    Plascore layup schedule

    Recent photos and where I am today with the project
    Post by: reelpleasure, Mar 2, 2014 in forum: Fiberglass and Composite Boat Building
  10. reelpleasure
    Thread

    Plascore layup schedule

    Nidacore layup schedule Hello ALL, I'm a bit new to this forum. You helped my out with suggestions on epoxying some limber holes. As I go...
    Thread by: reelpleasure, Mar 2, 2014, 1 replies, in forum: Fiberglass and Composite Boat Building
  11. reelpleasure
    Post

    Sealing the wood in limber holes

    Thanks for all your suggestions. The stringer in question is "new" and "dry". Finished today, 2 coats of epoxy in the hole heavy wetting the...
    Post by: reelpleasure, Mar 1, 2014 in forum: Fiberglass and Composite Boat Building
  12. reelpleasure
    Post

    Sealing the wood in limber holes

    OK, Today I drilled 1 3/8" holes where I need the drainage openings. I will insert 1 1/4 "PVC pipe pieces. Pieces are cut to the correct...
    Post by: reelpleasure, Feb 28, 2014 in forum: Fiberglass and Composite Boat Building
  13. reelpleasure
    Post

    Sealing the wood in limber holes

    Thanks to ALL for the replies. I'll triple coat the bare wood with West Systems epoxy
    Post by: reelpleasure, Feb 28, 2014 in forum: Fiberglass and Composite Boat Building
  14. reelpleasure
    Thread

    Sealing the wood in limber holes

    Curious, I have to drill a couple of limber holes through the new stringer pieces on the 25 T Jason. The limber holes on the old fir...
    Thread by: reelpleasure, Feb 27, 2014, 15 replies, in forum: Fiberglass and Composite Boat Building
  15. reelpleasure
    Thread

    Sealing the wood in limber holes

    Curious, I have to drill a couple of limber holes through the new stringer pieces on the 25 T Jason. The limber holes on the old fir...
    Thread by: reelpleasure, Feb 27, 2014, 2 replies, in forum: Wooden Boat Building and Restoration
  16. reelpleasure
    Post

    Filling thru hull holes

    Thank you
    Post by: reelpleasure, Dec 5, 2013 in forum: Fiberglass and Composite Boat Building
  17. reelpleasure
    Thread

    Filling thru hull holes

    Hello, ALL, I have an older lobster boat with a solid glass. I am doing a refit/rehab/repower and need to fill two or three holes in the...
    Thread by: reelpleasure, Dec 4, 2013, 5 replies, in forum: Fiberglass and Composite Boat Building
  18. reelpleasure
    Post

    on-line source for Cummins 4BT wet exhaust elbow

    Seaboard Marine www.sbmar.com Northeaster, get on Seaboard Marine's website...www.sbmar.com. read up on Tony's Tips, particularly about...
    Post by: reelpleasure, Dec 4, 2013 in forum: Diesel Engines
  19. reelpleasure
    Post

    Nidacore Test

    I read the labels !! Tunnels, I read the labels and used a "measuring cup" for the catalyst. I appreciate your feedback. Thank you,...
    Post by: reelpleasure, May 26, 2013 in forum: Fiberglass and Composite Boat Building
  20. reelpleasure
    Thread

    Nidacore Test

    Hello all, I have 2 or 3 questions. This is my "1st time" fiber glassing and I'm doing some testing of my skills or lack of finishing some...
    Thread by: reelpleasure, May 25, 2013, 3 replies, in forum: Fiberglass and Composite Boat Building
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2