Search Results

Search Again
Page 1 of 3
  1. Scrumble
    Post

    Difficult Cutting Problem - What Tool Would You Use?

    For acuracy, use a Bosch multitool and cut from both sides. See my use on my blog, use the metal blades through epoxy and glass.
    Post by: Scrumble, Nov 6, 2011 in forum: Boatbuilding
  2. Scrumble
    Post

    My little piece of peace

    Good Day Masalai, We have Michigan Wheel MP3's 15 x 11 for our 46C and we bought from:...
    Post by: Scrumble, Aug 31, 2011 in forum: Marketplace
  3. Scrumble
    Post

    New project, is my planning sound?

    Composite Building - re New project, is my planning sound? G'Day Groper, Congratulations on getting into building and solid planning about the...
    Post by: Scrumble, Jun 19, 2011 in forum: Fiberglass and Composite Boat Building
  4. Scrumble
    Post

    ghetto peel ply method

    Real Peel Ply If you use real peel ply and use it properly you will have an almost complete reduction in sanding. Peel ply is best, more cheaply,...
    Post by: Scrumble, Jun 14, 2011 in forum: Fiberglass and Composite Boat Building
  5. Scrumble
    Post

    "semi-stayed" riggs

    This concept would interest me.
    Post by: Scrumble, Aug 15, 2010 in forum: Multihulls
  6. Scrumble
    Post

    Graphite in Epoxy

    Mix graphite powder with silica (Cabosil, Aerosil) in epoxy and coat the bottom, this resulting very hard, very slippery and very black surface,...
    Post by: Scrumble, Aug 5, 2010 in forum: Materials
  7. Scrumble
    Post

    transporting a catamaran

    We could do it here in Australia, so there is a fair chance of doing it in you part of the USA. A good evaluation from a house moving company with...
    Post by: Scrumble, Jun 28, 2010 in forum: Multihulls
  8. Scrumble
    Post

    My Modular, Configurable, Trailerable, Containerable Cat Design pics are up!!!

    Its been done here http://www.cat2fold.com/index.php?page=pictures Regards,
    Post by: Scrumble, May 27, 2010 in forum: Multihulls
  9. Scrumble
    Post

    My little piece of peace

    I agree entirely.
    Post by: Scrumble, Feb 3, 2010 in forum: Marketplace
  10. Scrumble
    Post

    Dual helm stations, dual control heads for dual engines

    Thank you, powerabout for the link, its an excellent start.
    Post by: Scrumble, Feb 2, 2010 in forum: Diesel Engines
  11. Scrumble
    Thread

    Dual helm stations, dual control heads for dual engines

    I am building a motor/sailing cat, with inboard diesels. The helm locations are at 11m and 4.5m from each engine and the engines are greater than...
    Thread by: Scrumble, Feb 2, 2010, 2 replies, in forum: Diesel Engines
  12. Scrumble
    Post

    Building bomb-proof cleats/strong points.

    Good points about 5200 and 4200. I personally would prefer to follow the guidance of The Goudeon Brothers on Boat Construction.and use an epoxy...
    Post by: Scrumble, Jan 20, 2010 in forum: Fiberglass and Composite Boat Building
  13. Scrumble
    Post

    Marketing assymmetric multihulls

    Good Day, Most Bob Oram Design cats built so far have one dagger board. However Bobs designs include details of how to do two which are...
    Post by: Scrumble, Jan 11, 2010 in forum: Multihulls
  14. Scrumble
    Post

    Thrust transfer between shaft and output coupling on a V drive

    Thanks Frosty, I am happy with the interference fit as I may never have to take the coupling off. I will also ensure the set screws are set...
    Post by: Scrumble, Jan 3, 2010 in forum: Inboards
  15. Scrumble
    Post

    motorsailers vs large tides

    Suggest you have a look at http://boboramdesign.wordpress.com/39-c/ I realise you are only considering a monohull, however these will motor and...
    Post by: Scrumble, Jan 3, 2010 in forum: Motorsailers
  16. Scrumble
    Post

    Thrust transfer between shaft and output coupling on a V drive

    Good Day Gonzo, Thank you very much. Regards,
    Post by: Scrumble, Jan 2, 2010 in forum: Inboards
  17. Scrumble
    Post

    Thrust transfer between shaft and output coupling on a V drive

    Thrust transfer between shaft and output coupling on a ZF 15 MIV V drive Good Day Jango, Thank you for your reply, I need to clarify that the...
    Post by: Scrumble, Jan 2, 2010 in forum: Inboards
  18. Scrumble
    Thread

    Thrust transfer between shaft and output coupling on a V drive

    Thrust transfer between shaft and output coupling on a ZF 15 MIV V drive Good Day, Could anyone please advise me on the correct way to fit...
    Thread by: Scrumble, Jan 1, 2010, 8 replies, in forum: Inboards
  19. Scrumble
    Post

    What is difference between Epoxy & Polyester Resins

    2Sheets2Wind, You asked "What is difference between Epoxy & Polyester Resins" Strength
    Post by: Scrumble, Dec 27, 2009 in forum: Fiberglass and Composite Boat Building
  20. Scrumble
    Post

    Building bomb-proof cleats/strong points.

    It is better to build all the blocking in first, reinforce the deck, placing a large backing plate which in the case (my boat) below is also...
    Post by: Scrumble, Dec 27, 2009 in forum: Fiberglass and Composite Boat Building
Showing results 1 to 20 of 41 Next >
Search Again
Page 1 of 3