Search Results

Search Again
Page 1 of 2
  1. Brylk1830
    Thread

    Wiring in accessories

    Hi all, Well, I'm starting to think that the act of simply posting on this site- regardless of all the helpful replys I get- helps me solve any...
    Thread by: Brylk1830, Aug 23, 2008, 5 replies, in forum: OnBoard Electronics & Controls
  2. Brylk1830
    Post

    It works! One more question :)

    I was thinking the same thing about having a 15 amp fuse in an 8 gauge wire but it seems to be what the instructions show is needed....
    Post by: Brylk1830, Aug 18, 2008 in forum: OnBoard Electronics & Controls
  3. Brylk1830
    Thread

    It works! One more question :)

    Hello again, I want to thank everyone for helping me along the way, beginning with putting a new deck on my aluminum fishing boat, and up to...
    Thread by: Brylk1830, Aug 18, 2008, 2 replies, in forum: OnBoard Electronics & Controls
  4. Brylk1830
    Thread

    Installing Battery link ACR

    Hi again, http://bluesea.com/category/2/productline/overview/386 I'm installing the battery link acr and I have the wiring all figured out...
    Thread by: Brylk1830, Aug 17, 2008, 1 replies, in forum: OnBoard Electronics & Controls
  5. Brylk1830
    Thread

    What to use to crimp 8 AWG wire?

    I'm just wondering what I can use or buy to crimp 8 AWG size wire? My electrical pliers simply are too small and break the butt joint that I need...
    Thread by: Brylk1830, Aug 14, 2008, 18 replies, in forum: Electrical Systems
  6. Brylk1830
    Post

    Batterylink ACR installation question

    I found these fuse holders and I think they should get the job done. Cheap too!...
    Post by: Brylk1830, Jul 14, 2008 in forum: OnBoard Electronics & Controls
  7. Brylk1830
    Post

    Batterylink ACR installation question

    Is this the only thing I could get to plug those maxi-lite fuses into ? http://bluesea.com/category/5/21/productline/overview/127
    Post by: Brylk1830, Jul 14, 2008 in forum: OnBoard Electronics & Controls
  8. Brylk1830
    Post

    Batterylink ACR installation question

    Thanks Knotty, I looked at the max-fuses at West marine but wasn't sure what I need to get to hold the fuses? I have a glass fuse panel and was...
    Post by: Brylk1830, Jul 13, 2008 in forum: OnBoard Electronics & Controls
  9. Brylk1830
    Thread

    Batterylink ACR installation question

    Hi all, I just bought a battery link acr http://bluesea.com/category/2/productline/docs/386 and I think I understand how to hook it up but am...
    Thread by: Brylk1830, Jul 13, 2008, 6 replies, in forum: OnBoard Electronics & Controls
  10. Brylk1830
    Post

    How do I change my oil?

    My engine does have 3 cylinders but in my maintenance and warranty manual it briefly mentions Quicksilver NMMA/BIA Certified TC-W3 2-cycle...
    Post by: Brylk1830, Jun 22, 2008 in forum: Outboards
  11. Brylk1830
    Thread

    How do I change my oil?

    I have a 97 4O hp 3 cylin Mercury outboard and i'm wondering how to change the oil?
    Thread by: Brylk1830, Jun 22, 2008, 4 replies, in forum: Outboards
  12. Brylk1830
    Post

    Alternator charge wire

    I think you convinced me mack.. I have not bought anything yet but my local West Marine shop has both ACR and selector switches in stock. My...
    Post by: Brylk1830, May 12, 2008 in forum: OnBoard Electronics & Controls
  13. Brylk1830
    Post

    Alternator charge wire

    Here's the diagram
    Post by: Brylk1830, May 11, 2008 in forum: OnBoard Electronics & Controls
  14. Brylk1830
    Post

    Alternator charge wire

    Thanks again murdomack, I definitely agree that the ACR would be the best bet to ensure my batteries are charged seperately. Luckily, my local...
    Post by: Brylk1830, May 11, 2008 in forum: OnBoard Electronics & Controls
  15. Brylk1830
    Post

    Alternator charge wire

    Thanks red, so ultimatley I need a were coming from my solenoid to the starting battery and then a wire coming from my alternator neg as a ground...
    Post by: Brylk1830, May 10, 2008 in forum: OnBoard Electronics & Controls
  16. Brylk1830
    Thread

    Alternator charge wire

    I'm just wondering where my alternator charge wire (wire that supplies battery with charge) is located on my 99 Merc 3 cylin 2 stroke 40 hp...
    Thread by: Brylk1830, May 9, 2008, 8 replies, in forum: OnBoard Electronics & Controls
  17. Brylk1830
    Post

    options for two battery setup

    Thanks for the tip Fred. How would I install RV solenoid to the engine? I could probably figure it out if I could find one for sale online lol...
    Post by: Brylk1830, May 8, 2008 in forum: OnBoard Electronics & Controls
  18. Brylk1830
    Post

    battery systems

    What about the common ground slot on the switch?
    Post by: Brylk1830, May 6, 2008 in forum: Projects & Proposals
  19. Brylk1830
    Post

    options for two battery setup

    I think i'm going to go down to the local West Marine retailer tommorow afternoon and ask a few more questions before I start buying the supplies....
    Post by: Brylk1830, May 5, 2008 in forum: OnBoard Electronics & Controls
  20. Brylk1830
    Post

    options for two battery setup

    Thanks again Murdomack.. and btw my motor is a 97 4O hp 3 cylin Mercury outboard. Ok, just to get this all straight, and correct me if I'm wrong,...
    Post by: Brylk1830, May 5, 2008 in forum: OnBoard Electronics & Controls
Showing results 1 to 20 of 30 Next >
Search Again
Page 1 of 2