Search Results

Search Again
Page 1 of 2
  1. steele m.a.
    Thread

    Ford 302 in Campion

    My friend has a Campiion 24 minus engine. I'm thinking of building up a Ford 302 for the purpose , but don't know what drive the original I/O...
    Thread by: steele m.a., Mar 31, 2011, 1 replies, in forum: Sterndrives
  2. steele m.a.
    Post

    1974 455 Oldsmobile jetboat engine

    Fresh water getting into oilpan . Modify stuff - mate. Run semi - synthetic oil if you can . Pressurise the oilpan , old motors will do this by...
    Post by: steele m.a., Dec 31, 2010 in forum: Powerboats
  3. steele m.a.
    Post

    Merc 3 cyl 2 stroke

    Yes . Rough running beast . Owner has me holding dual throttle open to keep it alive. Won't idle - dies .
    Post by: steele m.a., Dec 25, 2010 in forum: DIY Marinizing
  4. steele m.a.
    Thread

    Merc 3 cyl 2 stroke

    I have a strange motor I need assistance with . A mercury 2 stroke , in a Bayliner 20 ski boat ( sterndrive ). It is a 3 cylinder vertical 2...
    Thread by: steele m.a., Dec 24, 2010, 3 replies, in forum: DIY Marinizing
  5. steele m.a.
    Thread

    Marinized Ford 429/460

    I'm marinizing 2 Ford 429 and 460 long blocks . They are to be installed into a Campion 24 and a Bayliner 20. I'm having difficulty locating wet...
    Thread by: steele m.a., Oct 28, 2010, 3 replies, in forum: Powerboats
  6. steele m.a.
    Post

    can anyone tell me what this boat is modeled after

    Good on ya then Want some assymetric sail hull plans ? S'new
    Post by: steele m.a., Oct 14, 2010 in forum: Sailboats
  7. steele m.a.
    Post

    can anyone tell me what this boat is modeled after

    That's a Dragon - 1930 - 30 feet long - 8 feet at Bmax . Fastest thing built before World War II venturehulls@gmx.com marksteele2010@yahoo.ca
    Post by: steele m.a., Jun 10, 2010 in forum: Sailboats
  8. steele m.a.
    Post

    Did a dream got shattered?

    Daq , Mark Steele . How can I access the sail/moment calculator from my home site ? marksteele2010@yahoo.ca
    Post by: steele m.a., May 18, 2010 in forum: Boat Design
  9. steele m.a.
    Post

    Bending Strength Of Aluminum Vs Wood?

    1100 Aluminum is pure aluminum , soft , bendable , not load carrying . 2117 Alloy has copper/zinc - Stronger , stiffer . Extruded , or wrought...
    Post by: steele m.a., Dec 31, 2009 in forum: Boat Design
  10. steele m.a.
    Post

    Fuel tank venting - what materials are ok?

    With fuel lines - even fuel vent lines - you have to consider flammability of the material you are building with , and you have to consider...
    Post by: steele m.a., Oct 6, 2009 in forum: Gas Engines
  11. steele m.a.
    Post

    Wet sanding with electric sander

    wetsand Try : NorthernTool.com
    Post by: steele m.a., Oct 1, 2009 in forum: Fiberglass and Composite Boat Building
  12. steele m.a.
    Post

    Closed Cooling System (Half)

    I'm building a similar system right now . It's for a 240 ci. mercury straight six . Original , the engine pumps raw water up , through itself and...
    Post by: steele m.a., Sep 23, 2009 in forum: DIY Marinizing
  13. steele m.a.
    Post

    Alternator question

    Alternator No - alternators only develop EMF ( voltage ) when their field windings and stator windings spin by each other , when a charge is...
    Post by: steele m.a., Jul 20, 2009 in forum: Gas Engines
  14. steele m.a.
    Post

    Alternator question

    79 Omc Don't build a short circuit into your boat . Any electrical system that uses an alternator , be it electronic ignition or points ,...
    Post by: steele m.a., Jul 20, 2009 in forum: Gas Engines
  15. steele m.a.
    Post

    Making a high efficency 3 Kw DC Generator

    24 Vdc :
    Post by: steele m.a., Apr 19, 2009 in forum: DIY Marinizing
  16. steele m.a.
    Post

    Making a high efficency 3 Kw DC Generator

    Hydraulic powered alternators are probably what you need . They are either 12V 24V , or , in your case 48V DC , but they are specialty sealed...
    Post by: steele m.a., Apr 19, 2009 in forum: DIY Marinizing
  17. steele m.a.
    Post

    New High Performance Monofoilers

    I'm working on a monohull in Victoria that is assymetric when heeled , symmetric when upright.25' x 30' , 620 sq. ft. of sail ....
    Post by: steele m.a., Mar 12, 2009 in forum: Sailboats
  18. steele m.a.
    Post

    Windward 928

    The boat - it was just reduced to $8,000.00 Mark
    Post by: steele m.a., Feb 25, 2009 in forum: Sailboats
  19. steele m.a.
    Post

    Windward 928

    $9,500.00 takes : boat wife - I'll miss the boat .
    Post by: steele m.a., Feb 23, 2009 in forum: Sailboats
  20. steele m.a.
    Thread

    Windward 928

    I currently run a Windward 928 , which is a 1980 hull , surveyed in 1999, with a new compliment of regatta sails , berths for 5 , propane...
    Thread by: steele m.a., Feb 20, 2009, 4 replies, in forum: Sailboats
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2