Boat Design Forums  |  Boat Design Directory  |  Boat Design Gallery  |  Boat Design Book Store  |  Thanks to Our Site Sponsors

Go Back   Boat Design Forums > Design > Propulsion
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #16  
Old 04-20-2005, 09:07 AM
bsmit24 bsmit24 is offline
Junior Member
 
Join Date: Mar 2005
Rep: 10 Posts: 17
Location: Louisiana
I just thought that moving the prop further aft, to approxiamately the same location that an outboard prop is that their might be some performance gains without making the drive significantly more complex. Its seems that moving the prop aft would allow you to raise everthing up and either reduce the drag and or run a larger prop. But you are correct about the rudder and that is something that I will have to workout.

I am not interested in surface drives but that seems to be only area of research.
Reply With Quote
  #17  
Old 04-20-2005, 10:16 AM
cyclops cyclops is offline
Senior Member
 
Join Date: Feb 2005
Rep: 33 Posts: 1,059
Location: usa
As a note. A uncupped prop of 2 blades is still USUALLY the most efficient. Thinner blades raise eff. also. Keeping the rpms low for a given size raises eff., but usually is not able to also give high speeds with high horsepower. Trade off time. A well designed and balanced hull is always the faster boat. Not stabile at speed? To busy worring to go fast. Speed requires the best knowledge of all the specialties.-----------------As a proof positive. Nuclear subs have the most eff. props. + 80 mph & faster at depth. The seatbelts are no joke.
Reply With Quote
  #18  
Old 04-20-2005, 03:52 PM
cyclops cyclops is offline
Senior Member
 
Join Date: Feb 2005
Rep: 33 Posts: 1,059
Location: usa
bsmit24, ask Volvo why the IPS drive is installed backwards under the stern.
Reply With Quote
  #19  
Old 04-20-2005, 05:15 PM
bsmit24 bsmit24 is offline
Junior Member
 
Join Date: Mar 2005
Rep: 10 Posts: 17
Location: Louisiana
I am not sure I understand the IPS question.

I had a buddy in the national quard that joined up after finishing in his tour in the navy sub fleet and he said that the speed was more like 30 to 35 knots. Was the 80+ mph a typo or did I miss something?
Reply With Quote
  #20  
Old 04-20-2005, 08:52 PM
cyclops cyclops is offline
Senior Member
 
Join Date: Feb 2005
Rep: 33 Posts: 1,059
Location: usa
The Nautilus, 1st Nsub ran away from our WWII 40 knot destroyer and off the sonar computer at 50 and accelerating fast. All NATO sonar operators had similar readings. We were fitted with a light cruisers steam chests, thats why we could do +40k. That is when we knew we would be a joke in a war zone. Our KILLER torpedos did 12K in attack mode.----------------- Volvo Ips is a stern drive mounted about where a shaft prop would be. It looks like a stern drive shoved right thru the hull with the prop always facing fowards. I take it that it should only feed solid water into the prop and all the prop thrust has to blow around both sides of the support. Less steering stalls and prop cavitation in a turn. Should be a little better than a I/O.----------------Nauti also fired a torp at the carrier. Accelerated passed the torp pulled along side the carrier and was hit by her own torp. That really drove the the point home to everyone.

Last edited by cyclops : 04-20-2005 at 08:57 PM. Reason: Slow recall.
Reply With Quote
  #21  
Old 04-20-2005, 09:43 PM
cyclops cyclops is offline
Senior Member
 
Join Date: Feb 2005
Rep: 33 Posts: 1,059
Location: usa
The "new" old woodies racing boats do sometimes have the rudder and prop at or 1' behind the transom. They are the 600-800hp powered 22' partial surface drives. It does make them more eff. and faster. 22' and + $120,000.
Reply With Quote
Reply



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
location of prop on Inboard k2panman Propulsion 7 03-01-2005 02:37 PM
Offset single prop - which direction? Ben Lindenberg Propulsion 7 11-10-2004 12:53 PM
sea ray prop for planing jfc52 Propulsion 20 09-17-2004 08:09 PM
Ideal depth of prop/ surface peircing props Sonnie00 Powerboats 2 08-01-2004 07:01 PM
Is this the right prop for this low speed inflatable? bill fish Powerboats 0 07-30-2004 11:57 AM


All times are GMT -5. The time now is 10:10 PM.


Powered by: vBulletin Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Web Site Design and Content Copyright ©1999 - 2012 Boat Design Net