| ||||
|
#1
| |||
| |||
| what means charge loop motor somebody can explain to me what means charge loop motor
__________________ Cristian |
|
#2
| ||||
| ||||
| Loop-Charging? Loop charge scavenging creates a circular flow in a cylinder for efficient removal of exhaust gasses and even distribution of the air-fuel mixture.The result is greater combustion efficiency for higher power and better fuel economy. www.yamaha-motor.co.nz/marine/
__________________ tomkane |
|
#3
| |||
| |||
| Thank you Tom. this produces an increase in rpm or no ? , example a motor not loop charging has 5500 rpm and one loop charging will has 6500 rpm in equality of conditions propela, hull, etc. If the answer is yes, whatever must be the normal rpm of a motor loop charging or range of rpm at top speed Thank you
__________________ Cristian |
|
#4
| ||||
| ||||
| Since the combustion chambers in a loop-charge type engine are a completely different shape than those of an old-style motor, it's impossible to make a fair comparison between them. But it would probably be safe to say that in general the loop-charge one will be able to turn lower rpm for comparable output, given identical displacement, fuel systems, etc.
__________________ - Matt Marsh - Marsh Design (small craft blog and designs) |
|
#5
| ||||
| ||||
| Loop charging design of a motor will give a more efficient motor and therefore give a higher RPM range.A motor not loop charged may also achieve high RPM.Loop charging is accepted as a good design feature of modern motors.if you have a loop charged motor (or any other motor)you should find an operating manual for the motor which will give clear operating instructions.You would need a revolution counter fitted to the motor to know what RPM the motor is operating at,5500 6500 would be a sensible top RPM.If you have no revolution counter and no operating instructions,run the motor up to full throttle then bring the throttle back to three quater throttle to cruise.
__________________ tomkane |
|
#6
| |||
| |||
| my boat is a 16" flat boat, with 140 hp loop charging year 89, with s.s. propeller 13 x 21, and in my revolution counter have 6500 rpm, and the motor is ok, but a donīt know if i can to maintain those rpm in normal conditions to much time without gamange it., becose I have not the owner manual. What do you think about it
__________________ Cristian |
|
#7
| ||||
| ||||
| The harder you run your motor the quicker it will wear out.You must be flying with that outboard on a sixteen foot flat bottom boat.Perhaps it is a heavy boat.Running at three quater throttle it should last longer.What is the name (make) of the outboard?
__________________ tomkane |
|
#8
| |||
| |||
| it is doing myself, but the hull is a magnum 16"
__________________ Cristian |
|
#9
| |||
| |||
| it is the boat, it flat boat to fiching, but is a vee hull with 21 š dedrise
__________________ Cristian |
![]() |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Solomon Technologies - "Electric Wheel" electric motor propulsion systems | lockhughes | Hybrid | 228 | 10-12-2011 05:00 PM |
| pontoon motor mount | kcard2112 | Boat Design | 1 | 05-11-2005 10:43 PM |
| short shaft motor on long shaft boat | ohenry | Boat Design | 0 | 03-21-2005 09:02 PM |
| Outboard Bracket Help | JOHN P. | Powerboats | 9 | 04-22-2004 08:24 AM |
| Combination CB trunk / Motor well | wwheeler | Wooden Boat Building and Restoration | 14 | 04-05-2004 10:05 PM |