Boat Design Forums  |  Boat Design Directory  |  Boat Design Gallery  |  Boat Design Book Store  |  Thanks to Our Site Sponsors

Go Back   Boat Design Forums > Design > Propulsion > Inboards
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 08-06-2011, 07:22 AM
whitepointer23 whitepointer23 is offline
Senior Member
 
Join Date: Jan 2011
Rep: 247 Posts: 655
Location: australia
hot water heater

hello, i have a 6 gallon hot water system that uses the starboard engine to heat it, it is only luke warm after and hour and a half of running the engine at 80 c, the motor is fresh water cooled. the engines that i removed were raw water cooled mercruisers, is it possible that the heater coils would salt up and cause this problem or are these heaters just very slow to heat water, i have never had one before to compare it.
__________________
brendan .
Reply With Quote
  #2  
Old 08-06-2011, 09:22 AM
CatBuilder CatBuilder is offline
Senior Member
 
Join Date: Jul 2009
Rep: 1316 Posts: 3,040
Location: With Apex1
Quote:
Originally Posted by whitepointer23 View Post
hello, i have a 6 gallon hot water system that uses the starboard engine to heat it, it is only luke warm after and hour and a half of running the engine at 80 c, the motor is fresh water cooled. the engines that i removed were raw water cooled mercruisers, is it possible that the heater coils would salt up and cause this problem or are these heaters just very slow to heat water, i have never had one before to compare it.
It should heat up faster than that.

You say you removed a raw water cooled engine and put in a fresh water cooled engine?

Did you ever try the water heater with the raw water engine running to compare before you changed to the fresh water engine?

In short, yes... it is quite possible for calcification to have narrowed the flow through the heating element if salt water was flowing through it for many years prior to the engine change.
__________________
Kurt Hughes was right about this place.
Reply With Quote
  #3  
Old 08-06-2011, 09:51 AM
Frosty's Avatar
Frosty Frosty is offline
Senior Member
 
Join Date: May 2002
Rep: 1693 Posts: 5,867
Location: Thailand
Are you heating the tank with fresh water or sea water.
Reply With Quote
  #4  
Old 08-06-2011, 11:38 AM
Bglad Bglad is offline
Senior Member
 
Join Date: May 2010
Rep: 67 Posts: 156
Location: Jacksonville, Florida
Working properly the heater connected to a freshwater cooled engine will scald you unless it is one the newer types with a mixing valve attached.
Reply With Quote
  #5  
Old 08-06-2011, 07:27 PM
powerabout powerabout is offline
Senior Member
 
Join Date: Nov 2007
Rep: 484 Posts: 1,431
Location: Melbourne/Singapore/Italy
where are the 2 pipes connected to the engine?
__________________
Boat builders are not necessarily Boat designers who are not necessarily Engineers who are not builders who are not designers.....
Reply With Quote
  #6  
Old 08-06-2011, 07:52 PM
iceboater iceboater is offline
Junior Member
 
Join Date: Jan 2011
Rep: 113 Posts: 49
Location: Iceland
If the heater is mounted above the outlet from the engine I would check for air in the heater. I use full pressure from water hose to get the air out and then I connect it to the engine.
Reply With Quote
  #7  
Old 08-07-2011, 04:07 AM
whitepointer23 whitepointer23 is offline
Senior Member
 
Join Date: Jan 2011
Rep: 247 Posts: 655
Location: australia
thanks for all the replys, i tried it again today and the water was scalding after running the engine 30 minutes. it may have been an airlock as iceboater says, the top of the heater is higher than the engine. it is fresh now frosty but the old engines were raw water. i never tried it with the old engines cat. the pipes run off the water pump and bypass outlet. once again thanks for the replys, i was over the moon when i had hot water today, never had a luxury like that on a boat before.
__________________
brendan .
Reply With Quote
  #8  
Old 08-07-2011, 07:22 AM
FAST FRED FAST FRED is offline
Senior Member
 
Join Date: Oct 2002
Rep: 756 Posts: 3,328
Location: Conn in summers , Ortona FL in winter , with big dock & room for O'nite stop .
cold beer and Ice cream are next!!
Reply With Quote
Reply



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Propane hot water heater location--rendering rsimon Materials 0 06-25-2011 01:40 AM
Propane hot water heater location--rendering rsimon Boat Design 12 06-16-2011 05:56 AM
Need som Hot water advice. thudpucker Boatbuilding 8 01-18-2010 02:18 AM
Hot Water Heater ORION1 Sailboats 8 08-15-2005 07:00 AM
On Demand Water Heater rjmac Boat Design 14 03-15-2005 05:45 AM


All times are GMT -5. The time now is 01:19 PM.


Powered by: vBulletin Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Web Site Design and Content Copyright ©1999 - 2012 Boat Design Net