Fiberglass and Composite Boat Building - Page 4

		Boat Design Forums > Construction > Boatbuilding
Fiberglass and Composite Boat Building

Page 4 of 51

Last »

Threads in Forum : Fiberglass and Composite Boat Building

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Tips on repair of this impact damage jayc	07-27-2009 04:45 PM by Itchy&Scratchy	8	312
New guy in need of help. ( 1 2) meangreen	07-27-2009 03:37 PM by meangreen	17	477
a one-off bow extension CDK	07-27-2009 03:30 PM by marshmat	9	352
Material Comparison johnny50	07-26-2009 02:06 PM by apex1	9	319
Carbon Fibre Steering wheel captainjsw	07-26-2009 11:15 AM by marshmat	3	292
Restoration Project: Adding Weight to Level Trim CapeCodAngler	07-25-2009 06:51 PM by apex1	3	243
Transom - dual to single ian_upton	07-24-2009 12:46 PM by ian_upton	8	369
Coosa Board Question SeaJay	07-23-2009 01:12 AM by SeaJay	7	475
stayless (free standing mast) tlar633	07-22-2009 03:32 PM by TeddyDiver	1	159
Hole Repair Methods and Materials MEJETSKI2000	07-21-2009 07:34 AM by MEJETSKI2000	0	187
Wooden Keel Hannibal	07-20-2009 03:19 PM by Hannibal	2	210
scaffolding help brokensheer	07-19-2009 03:34 PM by apex1	11	287
skin coat csm material brokensheer	07-19-2009 12:52 PM by SamSam	7	245
How long to leave a new mold before demolding alibi	07-19-2009 03:25 AM by tunnels	2	271
Interlux 2000/2001 vs. Interlux 3000/3001 stimulous check	07-18-2009 09:29 PM by alan white	3	153
Good finish for Interlux Epoxy 3000/3001 primer/barrier coat? stimulous check	07-18-2009 02:34 PM by PAR	4	315
question about fabricating long(20'+) stringers offshoreonly	07-16-2009 01:19 PM by offshoreonly	5	243
Replacing floor in 22' Crownline wingman65	07-16-2009 11:00 AM by SamSam	8	1,499
Joining a wooden deck to a fibreglass hull Sulian	07-15-2009 03:29 PM by Sulian	3	326
What should I remove first, Transom or Stringers? merrile	07-15-2009 12:00 AM by merrile	3	201
Addition of motor mount to stern schlever	07-14-2009 05:07 PM by schlever	2	197
Whats this "red stuff" ( 1 2 3) rwatson	07-13-2009 08:43 PM by rwatson	33	1,023
Epoxy, Resin or What ? MEJETSKI2000	07-12-2009 03:52 PM by PAR	7	313
Creating a mold from an existing part Dynafoiler	07-11-2009 10:13 PM by JRL	7	495
converting twin straight drives to a single outdrive david aymar	07-11-2009 09:32 AM by david aymar	0	116
transom shot jonesg	07-09-2009 02:12 PM by jonesg	4	507
The AWLGRIP Knowledge challenge ( 1 2 3 4 5 6 7 8 9 10 ... Last Page) grady	07-09-2009 04:28 AM by waikikin	562	37,826
Building a new deck / coachwork Sulian	07-05-2009 05:21 PM by apex1	9	432
To sand or not to sand, that is the question…. SeaJay	07-03-2009 09:11 PM by Jimbo1490	4	253
Help with transom fairing offshoreonly	07-02-2009 11:44 AM by offshoreonly	6	292
Alternative to Fiberglass and Epoxy? BIFFTHESKIFF	06-29-2009 03:11 PM by gonzo	9	719
Hull Extension Lay Up savagescout	06-28-2009 09:01 PM by tunnels	6	400
Need some help repairing soft spot in floor ( 1 2) Stan Bright	06-27-2009 03:33 AM by PAR	16	683
Is Balsa really that bad ?? ( 1 2 3 4 5 6 7) rwatson	06-26-2009 08:52 PM by masalai	90	2,764
Transom & Stringer replacement ( 1 2 3 4 5 6 7 8) blaze_125	06-25-2009 12:03 AM by blaze_125	105	5,762
Fibreglass hull layup questions. conlan	06-24-2009 03:59 AM by tunnels	3	524
Advice on a large project RE hull extension. Little Bighorn	06-22-2009 02:13 PM by Little Bighorn	0	370
Tool Recommendation Please ( 1 2 3) SeaJay	06-21-2009 01:15 AM by SeaJay	30	826
Basalt Fibres. tauruck	06-20-2009 12:27 PM by tauruck	13	595
Making a mold Clinton B Chase	06-19-2009 03:19 PM by SamSam	8	645

Mark This Forum Read

Page 4 of 51

Last »

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts vB code is On Smilies are On [IMG] code is On HTML code is Off

All times are GMT -5. The time now is 03:33 PM.