Fiberglass and Composite Boat Building - Page 2

		Boat Design Forums > Construction > Boatbuilding
Fiberglass and Composite Boat Building

Page 2 of 53

Last »

Threads in Forum : Fiberglass and Composite Boat Building

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
fiberglass lay up on c-flex 65 johnloucka	02-07-2010 07:18 PM by johnloucka	0	201
is tree sap on older gel-coat a big problem? Squidly-Diddly	02-07-2010 05:40 AM by tunnels	13	423
Can I (should I) build this boat this way fred breyer	02-07-2010 03:23 AM by TeddyDiver	7	407
cracked Cast iron keel on 37' sailboat ( 1 2) arosental	02-05-2010 10:59 AM by arosental	21	719
Fiberglass Center Console Restoration Tscott	02-02-2010 10:31 PM by rozoord	5	424
cowling repair toolsinbox	01-31-2010 01:12 AM by Itchy&Scratchy	4	149
Building Fiberglass Boats ( 1 2 3) wcnfl	01-29-2010 11:00 PM by CaptBill	41	1,851
rota moulding a rowing boat jcox911	01-26-2010 09:45 AM by jonr	11	285
Catastrophic delamination on a new Bertram ( 1 2 3) apex1	01-26-2010 07:41 AM by M-Sasha	36	2,342
Bedding stringers on foam Vice	01-24-2010 07:53 AM by gonzo	1	235
Fiberglass repair John Hanafin	01-23-2010 01:11 PM by Herman	5	340
gelcoat alternative dinoa	01-23-2010 01:10 PM by Herman	1	305
rub rail toolsinbox	01-23-2010 06:39 AM by missinginaction	8	291
Rebuild the old boat John FunBoat	01-22-2010 09:03 AM by John FunBoat	2	290
Proper way to clean foam panels pescaloco	01-20-2010 02:57 PM by tunnels	14	413
Building bomb-proof cleats/strong points. elhix	01-20-2010 08:31 AM by Scrumble	13	600
Deck-Hull Joint Dutch Peter	01-19-2010 06:17 PM by Speng	14	3,177
Plug building ( 1 2) Nick F	01-19-2010 04:23 AM by keith66	22	1,119
crack in fiberglass deck toolsinbox	01-18-2010 11:14 AM by toolsinbox	14	288
When is epoxy a bad choice? ( 1 2 3 4 5) souljour2000	01-18-2010 11:07 AM by souljour2000	64	1,989
Companionway garage, head platform/washbasin/shower mold in NZ Roly	01-18-2010 03:13 AM by tunnels	1	170
Pre-Release / Alligator Problem ( 1 2) Xander	01-17-2010 04:17 PM by tunnels	22	492
Cost of Carbon Vs. Fiberglas ryanpratt	01-17-2010 04:07 PM by tunnels	14	477
Small Part Stuck in Mold ( 1 2 3 4) wcnfl	01-17-2010 03:41 PM by tunnels	45	744
Who said resin infusion was easy? ( 1 2) ahender	01-17-2010 03:27 PM by Landlubber	15	892
32 Skater ( 1 2 3 4) G.G.	01-13-2010 04:55 PM by G.G.	57	1,770
glassing over stryofoam ( 1 2 3 4) Ron Skelly	01-12-2010 10:33 PM by ondarvr	45	1,306
Embedded nonslip fiberglass patterns BajaMike	01-12-2010 03:30 AM by Herman	11	778
Best way to add non-skid decking patern. ryanpratt	01-11-2010 10:24 PM by ryanpratt	1	196
polyethilene ( 1 2) zgubidani	01-10-2010 12:24 AM by pamarine	21	1,197
Major overhaul of fiberglass canoe ( 1 2) canoe42	01-09-2010 10:04 AM by ondarvr	15	2,239
Nanocrystalline Cellulose Dunno	01-07-2010 07:13 PM by Guest20100203	2	170
Opinion: cockpit sole resting/secured to integral fuel tanks pescaloco	01-07-2010 08:57 AM by pescaloco	3	114
Preparation between layers of glass/epoxy tdvjensen	01-06-2010 02:40 PM by Herman	4	254
Looking for supliers of 120 kg (A) grade polyester resin grpqueen	01-06-2010 09:45 AM by Herman	9	328
PVC or closed cell composites? 58ketch	01-06-2010 07:57 AM by 58ketch	8	626
Corner Fillets / Inside Radius Creation ( 1 2) Xander	01-05-2010 06:20 PM by Xander	19	710
Tabbing bulkheads techniques gregbe	01-03-2010 03:02 PM by keith66	6	339
What is difference between Epoxy & Polyester Resins ( 1 2 3 4 5 6 7) 2heets2wind	12-31-2009 02:10 PM by Fanie	99	3,636
Exhaust Lagging/Webbing zamgod	12-26-2009 07:25 PM by partgypsy	3	295

Mark This Forum Read

Page 2 of 53

Last »

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts vB code is On Smilies are On [IMG] code is On HTML code is Off

All times are GMT -5. The time now is 04:27 AM.